background image

 

 

 

INFORMATION TO USERS IN EUROPE 

 

NOTE 

 

CISPR 22 CLASS A DIGITAL DEVICE OR PERIPHERAL 

 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant 

to the European Union EMC directive.  These limits are designed to provide reasonable protection 

against harmful interference when the equipment is operated in a commercial environment.  This 

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 

accordance with the instruction manual, may cause harmful interference to radio communications.  

Operation of this equipment in a residential area is likely to cause harmful interference in which case the 

user will be required to correct the interference at his own expense. 

 

 

 

INFORMATION TO USERS IN THE U.S.A. 

 

NOTE 

 

FCC CLASS A DIGITAL DEVICE OR PERIPHERAL 

 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant 

to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful 

interference when the equipment is operated in a commercial environment.  This equipment generates, 

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 

instruction manual, may cause harmful interference to radio communications.  Operation of this 

equipment in a residential area is likely to cause harmful interference in which case the user will be 

required to correct the interference at his own expense. 

 

WARNING 

 

Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could void the user’s 

authority to operate the equipment. 

 

Use of unshielded plugs or cables may cause radiation interference.  Properly shielded interface cables 

with the shield connected to the chassis ground of the device must be used. 

 

 

 

 

 

 

EN60065 

Safety 

 

 

EN504192 2005 

Waste electrical products should not be 

disposed of with household waste. 

Contact your Local Authority for recycling 

advice 

EN55103-1: 1996 

Emission 

EN55103-2: 1996 

Immunity 

Summary of Contents for 570ASI-X19-10GE2









































Reviews: