background image

LED Table 

The table below describes the LED indication at various stages of Siren operation 

Status 

Strobe LED Indication 

Audible indication 

Full alarm 

Strobe light flashes brightly 

Siren piercing sound 

Installation is ok 
(Press tamper 
switch once 
after binding) 

LED flashes for 3 seconds 

Factory reset 

LED flash every 2 seconds for 
one minute 

Low battery 
indication 

LED flashes 20 times rapidly 

Specifications 

Battery 

6V 1.2Ah Lead acid, 9V PP3 alkaline 

Operating Temperature 

-10°C to 60°C

Working Range 

Minimum 200 meters 

Siren Volume 

Minimum 100dB / 1 meter 

Operating Frequency 

868MHz (EU)/ 923MHz (America) 

** Specifications are subject to change without notice.

           

WARNING: 

Do not dispose of electrical appliances as unsorted municipal waste, use separate 
collection facilities.   

Contact your local government for information regarding the collection systems 
available. 

If electrical appliances are disposed of in landfills or dumps, hazardous substances can 
leak into the groundwater and get into the food chain, damaging your health and 
well-being. 

When replacing old appliances with new ones, the retailer is legally obligated to take 
back your old appliance for disposal at least for free of charge. 

www.everspring.com 
3F., No. 50, Sec 1, Zhonghua Rd., Tucheng Dist., 
New Taipei City 23666, R.O.C 

A501112399R01

 

Summary of Contents for SE801

















Reviews: