background image

APPLICATION

XR luminaires are designed for use indoors, outdoors, wet locations, areas containing moisture, dirt, 

corrosion, vibration and rough usage.  The XR luminaire has been certified for use on marine vessels inside, 

outside, and in other severely wet saltwater environments. 

Certified to:   

UL 844, UL 1598, UL 1598A, and UL 8750;

 

 

 

CSA C22.2 No. 137, CSA C22.2 No. 250.0 and CSA C22.2 No. 250.13

   Hazardous 

Location 

Certication:

 

 

 

Class I, Division 2, Groups ABCD;

 

 

 

Class II, Division 2, Groups FG;

   Class 

III;

 

 

 

Class I, Zone 2, Group IIC;

   Zone 

22

   

Housing:  

 

Copper-free Cast Aluminium with Polycarbonate lens

Input Voltage:   

Based on luminaire suffix in table below: Suffix - AC: 120-277 VAC | Suffix - HV: 347-480 VAC  

Electrical Ratings: 

Connections:   

3 x 3/4” NPT Conduit | Black: Line | White: Neutral | Green: Ground

   

Optional:   Violet: 0-10V Dimming (+)  |  Grey: 0-10V Dimming (-)

  

 

 

For connections use wire rated to a minimum of 90°C.  Class 1 Wiring only.

 

 

 

All supply field wiring must be rated 300V minimum for luminaires with suffix AC, 

 

 

 

600V minimum for luminaires with suffix HV.

Ambient

Temperature Range:       Class I Division 2 | Class I Zone 2                   Class II Division 2 | Zone 22

    

XR8: -50°C to +75°C         T3C     

     All models -50°C to +50°C     T3C

                                                 

XR10: -50°C to +74°C      T3C

                                                 

XR15: -50°C to +74°C      T3C

                                                 

XR20: -50°C to +67°C      T3

Ingress Protection: 

IP66  | Suitable For Wet Locations. Marine Outside Type (Salt Water)

SURFACE/CEILING 

MOUNTING INSTALLATION

LUMINANCE

XR8 

XR10 

XR15 

XR20 

RATED VOLTAGE

[Volts]

RATED WATTAGE

[Watts]

INPUT

VOLTAGE

AC

HV

AC

HV

AC

HV

AC

HV

120-277
347-480
120-277
347-480
120-277
347-480
120-277
347-480

Flood: 47 Optic: 60
Flood: 49 Optic: 64
Flood: 55 Optic: 75
Flood: 58 Optic: 77

Flood: 84 Optic: 103
Flood: 91 Optic: 107

Flood: 141 Optic: 156
Flood: 148 Optic: 160

FREQUENCY

[Hz]

50/60
50/60
50/60
50/60
50/60
50/60
50/60
50/60

TM

Nemalux

I N D U S T R I A L

XR-HAZ

rev. A-13

E477829

1-14

www.nemalux.com  |   [email protected]  |   Tel 403•242•7475  |   Fax 403•243•6190 

MADE IN CANADA

E477829

*PENDING*

*PENDING*

Summary of Contents for XR-HAZ















Reviews: