background image

EVERLAST

 - SERIES 2000

 

Information regarding your EVERLAST Series 2000, Electric 

Water Heater.

Congratulations for choosing an Everlast™ Water Heater. The unit has been 

manufactured to Australian Standards AS 1056.1 and AS/NZS 60335.2.21, 

and incorporates a STAINLESS STEEL CYLINDER produced from marine 

grade stainless steel and which is  covered by a 10 year warranty as per the 

enclosed warranty conditions. The stainless steel cylinder gives longevity 

of service and also less maintenance because there is no sacrificial anode. 

The Everlast™ Series 2000 Electric Water Heater will provide continuous hot 

water for many years to come. 

1        Features of your Everlast™ Water Heater

The Everlast™ Series 2000 is an electric storage water heater that  

can be heated using standard or “off peak” electricity. Your electricity supply 

authority can provide you with information in relation to the “off peak” tariff 

applicable to your particular location.
The Everlast™ Series 2000 incorporates the latest aspects of design and 

material selection including :

  Marine Grade stainless steel cylinder,

   Control of thermal stratification, 

   Dual Positive Domed Cylinder resulting in optimum location of  

 

  element(s), water supply and delivery and flushing-through of  

 

  suspended solids.

   Highest level of insulation due to the use of a polymeric external    

  casing combined with thick polyurethane insulation.
The Everlast™ Series 2000 heats potable water in the storage  

cylinder by one or more immersion elements (depending upon model).
A thermostatically controlled electric element in the bottom of the  

cylinder can be connected to normal or “Off Peak” power supply. A  

second optional booster in the top half of the cylinder ( in twin element  

models ) is used to add additional hot water as required. The heated water 

rises up the cylinder by natural convection to the top where it is ready for use. 

As hot water leaves the storage cylinder, it is replaced by cold water, which 

enters at the bottom of the cylinder.

Everlast™ recommends flushing the water heater at regular intervals as 

advised by your licensed plumber, and to assist this operation, the cold water 

inlet has a large opening for flushing any built up solids that have escaped 

the line strainer.

EVERLAST MANUAL 16pp.indd   2

9/07/10   11:02 AM

Summary of Contents for series 2000

















Reviews: