EverHot 625275 Owner'S Manual And Installation Instructions Download Page 4

 

EVERHOT HEAVY DUTY GAS MAINS PRESSURE 

WATER HEATER WARRANTY - AUSTRALIA ONLY 

 

GAS WATER HEATER 625, 635 SERIES 275 MODELS 

 

1.

 

THE EVERHOT WARRANTY 

 GENERAL 

1.1 

This warranty is given by Rheem Australia Pty Limited ABN 21 098 823 511 of 1 Alan Street, Rydalmere 
New South Wales. 

1.2 

Rheem offer a trained and qualified national service network who will repair or replace components at 
the address of the water heater subject to the terms of the Everhot warranty. Rheem Service, in addition 
can provide preventative maintenance and advice on the operation of your water heater. The Rheem 
Service contact number is 131031, with Contact Centre personnel available 24 hours, 7 days a week to 
take  your  call  and  if  necessary  to  arrange  a  service  call  for  during  normal  working  hours  Monday  to 
Friday (hours subject to change). 

1.3 

For  details  about  this  warranty,  you  can  contact  us  on  131031  or  by  email  at 

[email protected]

 (not for service bookings). 

1.4 

The terms of this warranty and what is covered by it are set out in sections 2 and 3 and apply to water 
heaters manufactured from the 1

st

 May 2020. 

1.5 

If a subsequent version of this warranty is published, the terms of that warranty and what is covered by 
it will apply to water heaters manufactured after the date specified in the subsequent version. 

 

2.

 

TERMS OF THE EVERHOT WARRANTY AND EXCLUSIONS TO IT 

2.1 

The de

cision of whether to repair or replace a faulty component is at Rheem’s sole discretion. 

2.2 

If  you  require  a  call  out  and  we  find  that  the  fault  is  not  covered  by  the  Everhot  warranty,  you  are 
responsible  for  our  standard  call  out  charge. If  you  wish  to  have  the  relevant  component  repaired  or 
replaced by Rheem, that service will be at your cost. 

2.3 

Where  a  failed  component  or  cylinder  is  replaced  under  this  warranty,  the  balance  of  the  original 
warranty period will remain effective. The replacement does not carry a new Everhot warranty. 

2.4 

Where the water heater is installed outside the boundaries of a metropolitan area as defined by Rheem 
or  further  than  25 km  from  either  a  regional  Rheem  branch  office  or  an  Accredited  Rheem  Service 
Agent's  office,  the  cost  of  transport,  insurance  and  travelling  between  the  nearest  branch  office  or 
Rheem Accredited Service Agent’s office and the installed site shall be the owner’s responsibility. 

2.5 

Where the water heater is installed in a position that does not allow safe or ready access, the cost of 
that  access,  including  the  cost  of  additional  materials  handling  and/or  safety  equipment,  shall  be  the 
owner’s responsibility. In other words, the cost of dismantling or removing cupboards, doors or walls 
and the cost of any special equipment to bring the water heater to floor or ground level or to a serviceable 
position is not covered by this warranty. 

2.6 

This  warranty  only  applies  to  the  original  and  genuine  Everhot  water  heater  in  its  original  installed 
location and any genuine Everhot replacement parts. 

2.7 

The Everhot warranty does not cover faults that are a result of: 

a)  Accidental  damage  to the  water  heater  or  any  component  (for  example:  (i)  Acts  of God  such  as 

floods, storms, fires, lightning strikes and the like; and (ii) third party acts or omissions). 

b)  Misuse or abnormal use of the water heater. 

c) 

Installation not in accordance with the Owner’s Guide and Installation Instructions or with relevant 
statutory and local requirements in the State or Territory in which the water heater is installed. 

d)  Connection at any time to a water supply that does not comply with the water supply guidelines as 

outlined in the Owner’s Guide and Installation Instructions. 

Summary of Contents for 625275

















































Reviews: