manualshive.com logo in svg

EverHot 625275, Owner'S Manual And Installation Instructions

Share
Download
EverHot 625275 Owner'S Manual And Installation Instructions Download Page 2

  

An electronic copy of these Owner’s Guide and Installation Instructions is available upon request. 

PATENTS

 

This water heater may be protected by one or more patents or registered designs 

in the name of Rheem Australia Pty Ltd. 

TRADEMARKS

 

®

 Registered trademark of Rheem Australia Pty Ltd. 

TM

 Trademark of Rheem Australia Pty Ltd 

Note:

 Every care has been taken to ensure accuracy in preparation of this publication. 

No liability can be accepted for any consequences, which may arise as a result of its application. 

 
 
 
 

 Warning:

 Upon completion of the installation and commissioning of the water heater, leave this guide 

with the householder or responsible officer. 

DO NOT

 leave this guide inside of the cover of the water heater, 

as it may interfere with the safe operation of the water heater or ignite when the water heater is turned on. 

 
 

Summary of Contents for 625275

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands