EverFocus EQN22 Series User Manual Download Page 25 | Manualshive

Page: 25 / 44

background image

EQN2200

25

Press

Apply

to apply the setting changes or

Reset

to reset without saving the

change.

Video Recording Setting
User can set video recording by selecting one of the enabled video streams. This
will allow users to view live images while also recording video from another video
stream.
Video Stream: Select video recording stream from any enabled stream.
Video File format: Recording file will be saved as AVI or ARV, select which file
format is

to be used.

Press

Apply

to apply the setting changes or

Reset

to reset without saving the

change.

4.4.2 Camera

Camera Settings

The "Camera OSD setting" can be displayed on a video monitor and can be

Note: Total frame rate cannot exceed 60 fps.

System performance may be influenced if user enables 4 video streams

simultaneously.

«
...
23
24
25
26
27
...
»

Summary of Contents for EQN22 Series













































Reviews:

No comments

Related manuals for EQN22 Series

Brand: Panasonic Pages: 2

BL-C1A - Network Camera

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 8

Brand: CAME Pages: 80

SG2 BASE Series

Brand: Datalogic Pages: 62

Brand: Xiaomi Pages: 10

Brand: Digitus Pages: 9

JV-B765HV9V22DNR

Brand: JV vision Pages: 12

Brand: NAPCO Pages: 4

Brand: Takex Pages: 8

Brand: Vicon Pages: 28

AF-S NIKKOR 18-35mm f_3.5-4.5G ED

Brand: Nikkor Pages: 2

Brand: Digital Watchdog Pages: 12

Brand: Samcon Pages: 44

Brand: Sensor Espio Pages: 37

Brand: Vivotek Pages: 387

Brand: Idview Digital Pages: 2

DS-PDD12P-EG2-WB

Brand: HIKVISION Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands