background image

11                          For Professional Technical Support call 1-844-241-5521

 

 

Draining Pump 

 

Risk of electric shock

. Can shock, burn or 

kill. Disconnect power before working on pump or motor. 

 

1.

 

Pump down water level below all inlets to the pool.  

 

 

Risk of electric shock. Can shock, burn or 

kill. To avoid dangerous or fatal electrical shock hazard, 
turn OFF power to motor before draining pump. 

 

2.

 

Remove trap cover and use low pressure air to blow accumulated water from the piping system. Never use high pressure air to purge system. 

3.

 

Cap inlet piping after draining to keep water out of the pipes. 

4.

 

To prevent pump from freezing, remove trap cover and drain the tank body through the two drain plugs provided. Clean pump thoroughly; 
replace trap cover. 

 

 

Tighten trap cover by hand only (no wrenches)! If pump is not anchored, use caution to avoid breaking attached piping! 

 

5.

 

Be sure motor is kept dry and covered. 

Startup For Winterized Equipment 

1. Remove any temporary weather protection placed around system for shut down. 
2. Follow filter manufacturer’s instructions for reactivation of the filter. 
3. Inspect all electrical wiring for damage or deterioration over the shut-down period. Have a qualified service man repair wiring as needed. 
4. Inspect and tighten all water tight connections. 
5. Open all valves in suction and return piping. 
6. Remove any winterizing plugs in piping system. 
7. Drain all anti-freeze from system. 
8. Close all drain valves and replace all drain plugs in piping system. 
9. Prime pump according to instructions in Priming Pump. 

 

 

 

Pump should only be serviced by qualified personnel. For best results, use only genuine factory parts. Be sure to prime pump before starting. 

 

 

Risk of explosion. Before beginning pump service: 1. Stop pump before proceeding. 2. Close gate valves in suction and 

discharge pipes. 3. Release all pressure from pump and piping system. 

 

 

Risk of electric shock

. Can shock, burn or kill. Disconnect power before working on pump or motor. 

 

When using factory authorized parts, no lubrication or regular maintenance is needed beyond reasonable care and periodic cleaning of the strainer 
basket. 
If shaft seal is worn or damaged, repair as follows: 
 
 
 
 

Summary of Contents for SPP15002

















Reviews: