Evco EV3 MVC Series Applications Manual Download Page 64

Page: 64 / 74

EVCO S.p.A.

EV3 MVC & EVD MVC

| Application manual ver. 2.2c | Code 1443DMVCI224

page 64 of 74

ACCESSORIES

13.1

INTRABUS/RS-485 EVIF22ISX serial interface

Makes it possible to convert the INTRABUS signal into an RS-485 MODBUS signal (with INTRABUS communication protocol), to allow

connecting cables device-user interface up to 1,000 m.

EVIF22ISX can also work as programming key, to allow EV3 MVC and EVD MVC configuration upload and download.

USE AS PROGRAMMING KEY

Configuration upload

Place micro-switch 1, 2 and 3 of the three-positions DIP in position ON and micro-switch 1 and 2 of the two-positions DIP in

position ON.

Disconnect the controller from the mains; see the relative instruction sheet.

Connect the device to the INTRABUS port of the controller as shown in the section ELECTRICAL CONNECTION, or:

connect terminal 1 to terminal “12 V”

connect terminal 2 to terminal “data INTRABUS”

connect terminal 3 to terminal “reference (GND)”.

Power up the controller; see the relative instruction sheet.

The recognizing of the device will be run.

The recognizing normally takes a few seconds, when it is finished the green LED and the red LED will firmly switch on.

Later the configuration upload will be run.

The upload normally takes a few seconds. If the upload is succesfully completed, the green LED switches on firmly and the

red LED switches off; vice versa if the upload fails, the green LED switches off and the red LED switches on firmly (repeat the

upload).

Summary of Contents for EV3 MVC Series











































































Search results

Summary of Contents for EV3 MVC Series

Reviews:

Related manuals for EV3 MVC Series

Brands by name

Popular brands

Evco EV3 MVC Series, Applications Manual

Search results

Summary of Contents for EV3 MVC Series

Reviews:

Related manuals for EV3 MVC Series

Brands by name

Popular brands