Evco EV3 MVC Series Applications Manual Download Page 12

Page: 12 / 74

EVCO S.p.A.

EV3 MVC & EVD MVC

| Application manual ver. 2.2c | Code 1443DMVCI224

page 12 of 74

The pictures below show how to install the EVD MVC.

To remove the EVD MVC, first remove any plug-in screw terminal blocks fitted in the lower part, then, using a screwdriver, loosen the

DIN rail clip, as shown in the pictures below.

To re-install the EVD first press the DIN rail clip fully in.

3.3

Measurements and installation of EV3K11

The pictures below show the measurements of EV3K11; measurements are expressed in mm (inches).

To be installed on a panel with the snap-in brackets provided.

The thickness of the panel on which the EV3K11 is to be installed must be between 0.8 and 2.0 mm (0.031 and 0.078 in).

Summary of Contents for EV3 MVC Series











































































Search results

Summary of Contents for EV3 MVC Series

Reviews:

Related manuals for EV3 MVC Series

Brands by name

Popular brands

Evco EV3 MVC Series, Applications Manual

Search results

Summary of Contents for EV3 MVC Series

Reviews:

Related manuals for EV3 MVC Series

Brands by name

Popular brands