Evco EV3 MVC Series Applications Manual Download Page 62

Page: 62 / 74

EVCO S.p.A.

EV3 MVC & EVD MVC

| Application manual ver. 2.2c | Code 1443DMVCI224

page 62 of 74

Code

Label on display

Description

AL16

Artc

Clock alarm

The alarm signal is activated when the clock shows an invalid date or is damaged and time band

regulation is activated (t01).

Automatic alarm.

Main results:

- regulating using the clock is not permitted

AL17

AL18

AFLS

AFLr

Supply or return flow alarm

The alarm signal is activated when the input configured as a flow switch (for either supply or

return) is active for a time period equal to A07, with a delay of A06 from the switch-on of the

associated fan; it is deactivated when the input is inactive for a time period equal to A08.

It reverts to manual reset if the number of alarm events in an hour exceeds A09.

Main results:

- when the alarm is in automatic mode the electric coils and the compressor are switched off

- when the alarm is in manual mode all the loads are switched off

AL19

ACnf

Changeover probe not configured alarm

The alarm is activated if the changeover probe has not been configured correctly.

Automatic alarm.

Main results:

- inhibits the automatic changeover operations

AL20

AL22

AV1

AV2

Water temperature congruence alarm

The alarm signal is activated in heating (cooling) mode if the water probe temperature is lower

(higher) than the temperature setpoint value, after a period equal to A13 seconds from when the

water valve is opened and for a period of A13 seconds from when the condition occurs. It is

deactivated when the temperature remains above the se C37/2 (setpoint - C38/2) for a

period of A13 x 10.

It reverts to manual reset if the number of alarm events in an hour exceeds A05.

Main results:

- the associated water coil is switched off

AL21

ASF

Filter pressure switch alarm

The alarm is activated if the input configured as filter pressure switch is active. It is deactivated if

the input is inactive.

Automatic alarm.

Main results:

- signal only

AL23

ACnG

Digital input congruence alarm

The alarm is activated if the

Heat pump status

digital input is configured and the following

settings are not applied:

Heat pump status (NO)

= 1 and the machine is in heating mode

Heat pump status (NC)

= 0 and the machine is in heating mode

Heat pump status (NO)

= 0 and the machine is in cooling mode

Heat pump status (NC)

= 1 and the machine is in cooling mode

Automatic alarm.

Main results:

- the water valve is switched off

AL24

AFir

Fire alarm

The alarm is activated if the input configured as

Fire Alarm

is active. It is deactivated if the input

is not active.

Manual alarm.

Main results:

- If C68 = 0 (fire management) all the loads are switched off

- If C68 = 1 (smoke management) the coils are switched off, and the fans and the dampers are

set to maximum.

Summary of Contents for EV3 MVC Series











































































Search results

Summary of Contents for EV3 MVC Series

Reviews:

Related manuals for EV3 MVC Series

Brands by name

Popular brands

Evco EV3 MVC Series, Applications Manual

Search results

Summary of Contents for EV3 MVC Series

Reviews:

Related manuals for EV3 MVC Series

Brands by name

Popular brands