EVBox Audi Wallbox Installation And User Manual Download Page 48

Page: 48 / 74

Place the front cover onto the main

assembly by using the provided hooks of

the front cover. Mount the front cover by

tightening the six screws M4 x 10 mm.

Align the bezel with the UP arrow on the

inside pointing up. Push the bezel onto

the front cover so it locks in position.

10.

Wind the charging cable around the

wallbox for proper storage.

11.

Turn on the input power of the wallbox.

The wallbox state LED comes on to show that

the wallbox is starting up to become ready

to charge. See chapter Status indication for

more information.

After successful installation, the certified

electrician must provide the user with a com-

missioning protocol. If you need a commis-

sioning protocol, you can download it from

www.elli.eco/download.

Summary of Contents for Audi Wallbox











































































Search results

Summary of Contents for Audi Wallbox

Reviews:

Related manuals for Audi Wallbox

Brands by name

Popular brands

EVBox Audi Wallbox, Installation And User Manual

Search results

Summary of Contents for Audi Wallbox

Reviews:

Related manuals for Audi Wallbox

Brands by name

Popular brands