Model PRO711
Ultra Fast NiMH / NiCd Charger
Owner’s Manual
Thank you for purchasing the NoMEM PRO Battery System. Please read this manual carefully. It contains important
operating instructions for your NoMEM PRO Rechargeable Battery System. This PRO711 Ultra Fast charger will quickly
and efficiently charge all AA or AAA Nickel Cadmium (NiCd) or Nickel Metal-Hydride (NiMH) batteries. The built-in high
efficiency “switching” type power supply will adjust automatically to any voltage from 100 – 240VAC, for international use.
Warning:
•
Batteries are not charged as shipped. Must be charged prior to first use.
•
Charge
only
NiCd or NiMH type batteries on this charger.
•
Do Not
mix NiCd and NiMH batteries together when charging or using. Keep all NiMH batteries and NiCd batteries
separate.
•
Use only NoMEM PRO or other proper NiMH compatible charger to recharge NoMEM PRO batteries.
•
Batteries may leak or explode causing personal injury if inserted improperly, disposed of in fire, mixed with other
battery types, or short circuited.
Charging Instructions
1.
The battery compartment is adjustable to fit either AA or AAA size batteries. If you are charging AAA size batteries,
make sure the small tab, at the top of the battery compartment, has been moved all the way down until it has clicked
into place. If you are charging AA size, make sure the tab is lifted all the way up, into the notch located at the top of
the battery compartment. After adjusting the compartment to fit the size batteries you wish to charge, insert either 2
or 4 AA or AAA batteries into the charger. Do not mix AA and AAA batteries when charging.
2.
Flip out the AC prongs, built into the back of the charger, and plug into any available 100-240VAC outlet. The built-in
switching power supply will adjust automatically. When using overseas, a proper plug adapter may be required (not
supplied). The status LED will glow red over each compartment where the batteries are receiving charge.
3.
After charge is complete, the “status” LED will change to green to indicate that the charge is complete and batteries
are ready for use. Once the status LED is green, the charger switches to “trickle” mode to keep the batteries at full.
4.
Once charge is complete, remove batteries and unplug charger as soon as it is practical. Do not leave batteries in
charger for extended periods of time (more than 1-2 days)
OR
when the charger is not plugged in. Unplug the
charger when not in use.
5.
Begin again at
Step-1
to charge the next set of batteries.
Bad Cell Detection:
When charge process is started, the charger detects the health status of each of the cells in the battery compartment. If
any battery is unsuitable for charging, i.e. short circuit or reversed polarity, the status LED will flash.
The damaged cell(s)
should be properly disposed of.
Charging Times:
Size /
Type
Capacity
C
C
h
h
a
a
r
r
g
g
e
e
T
T
i
i
m
m
e
e
*
*
AAA /
NiCd
240-
300mAh
60 minutes
AAA /
NiMH
600-
750mAh
120 minutes
AA / NiCd
600-
800mAh
60 minutes
AA / NiMH
1400-
1600mAh
120 minutes
AA / NiMH
1800mAh
140 minutes
*
*
C
C
h
h
a
a
r
r
g
g
e
e
t
t
i
i
m
m
e
e
w
w
i
i
l
l
l
l
v
v
a
a
r
r
y
y
w
w
i
i
t
t
h
h
t
t
h
h
e
e
c
c
a
a
p
p
a
a
c
c
i
i
t
t
y
y
,
,
c
c
o
o
n
n
d
d
i
i
t
t
i
i
o
o
n
n
,
,
a
a
n
n
d
d
a
a
m
m
o
o
u
u
n
n
t
t
o
o
f
f
c
c
h
h
a
a
r
r
g
g
e
e
l
l
e
e
f
f
t
t
i
i
n
n
t
t
h
h
e
e
b
b
a
a
t
t
t
t
e
e
r
r
y
y
t
t
o
o
b
b
e
e
c
c
h
h
a
a
r
r
g
g
e
e
d
d
.
.
