manualshive.com logo in svg

EUTECH INSTRUMENTS CyberScan pH 10, Instruction Manual, Page: 56 / 67

Share
Download
EUTECH INSTRUMENTS CyberScan pH 10 Instruction Manual Download Page 56

52

13 TROUBLE-SHOOTING

PROBLEM

PROBABLY CAUSE

REMEDIAL ACTION

Nothing is displayed when the
ON/OFF key is selected.

1. 

Batteries not in place.

2. 

Batteries (+ & - poles) not in
correct polarity.

3. Weak 

batteries.

1. Insert 

batteries.

2. 

Re-insert batteries in the
correct polarity.

3. 

Replace batteries or attach
AC adapter.

Unstable reading

1. 

Insufficient reference
electrolyte in electrode.

2. Broken 

electrode.

3. 

External “noises” or induction
(e.g. electrical ‘noise’ caused
by a nearby motor).

4. Dirty 

electrode.

1. 

Fill electrode with reference
electrolyte.

2. Replace 

electrode.

3. 

Remove or switch off
interfering device.

4. 

Clean the electrode.
Rejuvenate if necessary.

Slow responses.

1. 

Dirty electrode.

1. 

Clean electrode. Rejuvenate
if necessary.

Meter is not responding to key
press.

1. 

HOLD mode in operation.

2. Broken 

electrode.

3. Internal 

program 

error.

1. 

Cancel HOLD mode.

2. Replace 

electrode.

3. 

Reset all internal programs
by re-inserting battery.

Summary of Contents for CyberScan pH 10




































































Reviews:

No comments