manualshive.com logo in svg

EUTECH INSTRUMENTS CyberScan pH 10, Instruction Manual, Page: 20 / 67

Share
Download
EUTECH INSTRUMENTS CyberScan pH 10 Instruction Manual Download Page 20

16

4.4.2 

Temperature Calibration With ATC Probe

1. 

Make sure the ATC probe is attached to the meter.

Refer to Figure 7 in Section 3.2.2.

2. 

Switch the meter on. Note the ATC indicator.

3. 

Press the MODE key to select temperature mode,

[Temp].

4.  Dip the ATC probe into a solution of known

temperature (i.e. a temperature bath). Allow time for

the temperature probe to stabilize.

5.  Press the CAL/MEAS key to enter temperature

calibration mode. The primary display indicates the

pH value, and the secondary display shows the

temperature.

6. Press 

!

 or 

"

 key to select temperature.

7.  Once you have selected the correct temperature,

press CON key to confirm.

8.  The CON indicator flashes for one second and

disappears.

9.  Press CAL/MEAS key to return to the pH

measurement mode.

NOTE:  To exit this program without confirming the

temperature calibration value, DO NOT press CON.

Press CAL/MEAS instead.

Figure 19: Temperature calibration

with temperature probe

Summary of Contents for CyberScan pH 10




































































Reviews:

No comments