Eusso UGL2430-RTA User Manual Download Page 8

Page: 8 / 68

Chapter 2 Installation

This chapter offers information about installing your router. If you are not familiar with the hardware or software

parameters presented here, please consult your service provider for the values needed.

2.1 Checklist

Check the shipping box carefully to ensure that the contents include the items you ordered. If any of the items are

missing or damaged, contact your local distributor. The contents of your carton may vary depending on your

service provider.

Contents description

1) Wireless 11n Router for home/office use

2) Wireless 11n Router Installation and Operation Guide (this publication)

3) Power supply with 9VAC / 1Ampere power adapter

4) Ethernet cable Ethernet category 5 twisted pair cable (6 ft)

5) CD for user manual

Summary of Contents for UGL2430-RTA




































































Search results

Summary of Contents for UGL2430-RTA

Reviews:

Related manuals for UGL2430-RTA

Brands by name

Popular brands

Eusso UGL2430-RTA, User Manual

Search results

Summary of Contents for UGL2430-RTA

Reviews:

Related manuals for UGL2430-RTA

Brands by name

Popular brands