Water
•
Use tap water for all your cleaning
needs.
•
However, if you live in an area with
hard water, use de-mineralized /
distilled water when steaming light
colored fabrics to eliminate the
possibility of hard water stains.
IMPORTANT:
Do
NOT
add cleaning
solutions, scented perfumes, oils or any
other chemicals to the water used in
this appliance.
Use tap water or
distilled/purified water if the tap
water in your area is very hard.
Efficient Work
• For vertical surfaces, wipe with a
towel from the top down, in this
way the dirty water will not soil
surfaces already cleaned.
•
Avoid changing brushes back and
forth while cleaning.
•
Start with the smallest brush to
clean tight spots and corners first.
•
Use a towel to wipe dirt as soon as
possible, otherwise it will dry and
re-adhere to the surface.
If you consistently use demineralized or
distilled water, cleaning the tank is
unnecessary.
Rinsing Out the Steam Cleaner
Normally, a periodic rinse of your steam
cleaner will free it from deposits. This is
recommended every 10-15 tankfulls, to
free up any scale deposits from the tank.
Fill the boiler with 20 oz. of water and
shake the cleaner vigorously. Tilt the
cleaner upside down to empty the boiler of
water and any scale deposits.
Descaling Your Steam Cleaner
If the tap water in you area contains a high
level of calcium deposits and you have
been using tap water to do your steam
cleaning, you should descale your unit
after 10-15 tankfulls.
Step 1:
Unplug the steam cleaner from
the power source before you
descale the boiler. Allow to cool.
Step 2:
Fill the boiler with 1 part
vinegar and 5 parts water and
leave overnight or for a period
of approximately 8 hours. Do
not screw the safety/filler cap
onto the steam cleaner while
you are descaling the boiler.
Do not use the steam cleaner
while descaling solution is
inside the boiler.
Step 3:
After the period of soaking, turn
the steam cleaner upside down
to empty solution from the
boiler. Due to the fact that a
small amount of solution will be
left in the boiler, it is necessary
to rinse the boiler out with clean
water 2 or 3 times. Your steam
cleaner is now ready for use.
Note:
When storing your unit, always
drain any residual water in the boiler and
do not tighten the safety filler cap onto the
unit. Always leave the safety filler cap
loose on the unit when not in use.
To Descale the Steam Cleaner
Care and Maintenance
To Order Additional Supplies
Note: If you need to order supplies such
as steam pocket towels, soap kits, etc.
please call the customer service number
at 1 (800) 798-7398.
TIPS ON HOW TO USE YOUR SYSTEM
OPERATING INSTRUCTIONS
Components
Power “On” Light (red):
This light will
illuminate when the unit is plugged into
the 120V. wall outlet. This light will cycle
on and off with the steam ready light.
CAUTION:
Read the instructions
for “Filling the Water Tank” before
opening the Safety Cap.
CAUTION:
Always unplug
before filling.
ALLOW UNIT TO
COOL FOR FIFTEEN (15)
MINUTES BEFORE REFILLING.
IMPORTANT:
Do
NOT
add cleaning
solutions, scented perfumes, oils or any
other chemicals to the boiler in this
appliance.
Use tap water or
distilled/purified water if the tap water
in your area is very hard.
Filling or Refilling Your Steam
Cleaner With Water
IMPORTANT:
Always insure that the unit
is “UNPLUGGED” from the wall receptacle
prior to initial filling or re-filling the water
tank and has been allowed to cool for 15
minutes.
Never attempt to fill this unit
under a water tap
,
always use the filling
funnel provided.
Step 6:
Connect desired attachments
onto the Flexible Steam Hose.
Step 7:
Plug the unit into a standard (120
volt, grounded) wall receptacle.
Allow approximately 8-10 minutes
for vapor to reach its working
temperature and pressure. The
green ready light will illuminate
when the unit is ready for use.
Always point nozzle outlet in a safe
Remove the funnel slowly and let
the remaining water in it to go
inside the water tank.
Do Not
Overfill
. Replace the Safety
Filler Cap.
WARNING:
Allow unit to cool
for 15 minutes before refilling
.
When refilling the steam cleaner
while the boiler is still hot,
there is
a risk that water will squirt back
during filling and cause scalding.
Extreme care should be taken
when refilling the unit. Use
caution when opening the
Safety/Filler Cap as cap may
become hot during use and
escaping steam can cause
scalding.
Step 1:
Before refilling the steam cleaner,
make sure that the unit is
NOT
plugged in and has been allowed to
cool for fifteen (15) minutes.
Step 2:
Plug the power cord in to an electrical
outlet and press the steam switch on
the hand grip to the “ON” position to
vent of any residual steam that is in
the boiler.
Step 3:
Remove the power cord from the
electrical outlet and turn the steam
switch on the hand grip to the “OFF”
position.
Step 4:
Place the unit on a flat, stable
surface. Slowly turn the safety filler
cap counter clockwise until it is
removed.
Step 5
: Insert the funnel into the tank
opening and add 40 US Fl, Oz.
(1200 ml) of water. (Fig. 1) Place the
funnel in the tank opening as
illustrated in Fig. 1. The funnel has
been specially designed to show
when the water tank is full. When
water starts to come out of the vent
hole of the funnel, the tank is full.
WARNING:
Allow unit to cool
for 15 minutes before refilling
.
Use caution when opening the
Safety/Filler Cap as cap may
become hot during use and
escaping steam can cause
scalding.
direction.
NOTE:
When the steam cleaner has run
out of water, steam output will
cease.
Fig. 1
5
12
Summary of Contents for SELECT EP923H
Page 2: ......
