manualshive.com logo in svg

EUCHNER CES-AP-C01- Series, Operating Instructions Manual

Share
Download
EUCHNER CES-AP-C01- Series Operating Instructions Manual Download Page 25

25

112663-05-03/15 (translation of the original operating instructions)

Operating Instructions

Non-Contact Safety Switch CES-AP-C01-…

EN

6.4.  Technical data of actuator CES-A-BRN

Parameter

Value

Unit

min.

typ.

max.

Housing material

PPS

Dimensions

80 x 40 x 15

mm

Ground

0.06

kg

Ambient temperature

- 25

-

+ 70

°C

Degree of protection acc. to EN IEC 60529

IP67

Installation position

Active face opposite read head

Power supply

Inductive via read head

6.4.1.  Dimension drawing

 

Active face

 

Active face

40

80

10,3

5,5

17

11

17

11

15

8,5

NOTICE

2 safety screws M5 x 16 included.

6.4.2.  Operating distances
Operating distance for center offset m = 0

Parameter

Value

Unit

min.

typ.

max.

Switch-on distance

-

27

-

mm

Assured switch-on distance s

ao 1)

20

-

-

Switching hysteresis 

1)

-

3

-

Assured switch-off distance s

ar

-

-

75

1) The values apply for surface installation of the actuator on steel.

Summary of Contents for CES-AP-C01- Series

































Reviews:

No comments

Brands by name

Popular brands

Load more brands