background image

5

www.etna.com.tr

3. Control Board Front Panel

•  General Fault Led: 

This led is ON together with written fault code on 7 segment display 

when low current , high current, low voltage and high voltage protections are active.

•  Up / Down Buttons: 

These buttons enable to surf within menus on 7 segment display and 

they are used to set values of numerical parameters. In addition to this, the fault occured on 

the system can be reset while pressing these buttons together for 5 seconds 

•  Approval Button:

 This button enables to enter submenus and save the parameter already 

set values.

•  Switch Led: 

This led is ON when the pressure swith on the system is active. 

•  ON/OFF Button: 

 This button is used to start-up and switch-off the panel OFF is written on 7 

segment display when the panel is switched-off and there is power supply on the system. 

Voltage value between L1-L2-L3 and neutral is 

displayed in sequence as seen on the left hand side 

when there is no run signal. In case there is run 

signal and system starts operating, pump current is 

displayed.

When the "Confirm" button is pressed in the main 

operation screen, the password menu on the left 

appears. In the password menu, “132” is entered as 

the password with the “Up / Down and Confirm” 

buttons, and the menu is entered by pressing the 

confirm button again. The password is valid for 2 

minutes.

After the password is entered correctly, the High 

Voltage Limit Setting Menu will appear on the 

screen. By pressing the "Confirm" button again, 

it is entered into the menu and the high voltage 

protection value is set with the "Up / Down" 

buttons. The limit value is set at the factory and 

changing this value is not recommended.

4. Menus

a.  Password Menu

b.  High Voltage Protection Setting Menu 

Figure 4. Panel Main Operating Screen

Figure 5. Password Menu

Figure 6. High Voltage Limit Setting Menu

Summary of Contents for Hydropan-Single













Reviews: