6.5 in.
3.6 in.
6.5 in.
3.6 in.
1.4 in.
.25 in.
A
B
Model # 53901111
Part # WP-8IN-2000LM-8-CP3-MV-OS-BZ
Certification # 53901111
USe aNd Care GUIde
Led WaLL PaCK WIth MOtION SeNSOr
NOte
:
Keep your receipt and these instructions for proof of purchase.
WarNING
:
Shut off the power at the circuit breaker or fuse panel before removing the old
fixture, ballast, or fluorescent tubes.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician
to do the installation.
INSTALLATION
Shut off power at the electrical panel before beginning the installation.
Remove existing fixture and set aside to recycle in accordance with local requirements.
WarNING:
RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker before removing the
existing light fixture or installing the new one. • Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so
could lead to electric shock, fire, or other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or
turn off the circuit breaker. • Risk of fire or electric shock. Installation requires a person familiar with the construction and operation of the light fixture’s/luminaire’s electrical system
and the hazard involved. If not qualified, do not attempt installation. Contact a qualified electrician.
NOtICe:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
Remove the two screws at
the top of the wall pack and
remove the lens by rotating
the lens down and sliding it to
the right.
3
4
PAckAgE cONTENTS
Part Description
Quantity
A Fixture
1
B Lens
1
C Drywall Anchor
4
D Mounting Screw
4
E Wire Connector
3
F
Gasket
1
1
2
Place the fixture in the desired location and mark the
locations of the mounting holes.
Set the fixture aside until ready.
Drill a 1/4-in. pilot hole into each marked location.
If mounting the fixture to drywall, install a drywall
anchor into the mounting holes
NOte
: Mounting screws are suitable for wood and
concrete mounting.
5
Use a power drill to drill through the
mounting holes on the fixture.
Align the fixture with the electrical box to
determine which knock outs to remove for
mounting.
Drill out the required knock outs with a
power drill.
6
Place the gasket on the
back of the fixture and feed
wires from the electrical box
through the desired knock
out hole.
US Patents - 10,091,855, 10,462,871, 10,492,262
B
A
E
D
Align the holes on the fixture with the
mounting holes on the electrical box and
align the mounting holes on the fixture
with the pilot holes drilled in the mounting
surface.
• Insert the 4 mounting screws and
tighten to secure the fixture to the wall.
7
8
Reattach the lens to the fixture.
Restore power at the electrical
panel.
Turn on the light switch to
activate the fixture.
11
• Slide the holes in the bottom of the lens over
the pegs at the bottom of the fixture.
• Make the electrical connections:
• Black wire to black wire.
• White wire to white wire.
• Connect ground wire from the electrical box to the
ground wire from the fixture.
Use wire connectors to cover the wire connections and
wrap with electrical tape.
• Connect the green quick connectors from the fixture
to the lens.
• Connect red and blue wire quick connectors from the
fixture to the lens.
9
Set the desired timer setting
(5min/15min/disabled)
10
Use the Color Preference
®
switch to select the
desired color temperature.
12
Apply silicone caulk (not
included) to the edges of the
fixture.
Color temperature
adjustment gear
C
F
