EtherWAN EX24000 User Manual Download Page 18

Page: 18 / 239

UNPACKING AND INSTALLATION

This chapter describes how to unpack and install the EX24000 Switch

The topics covered in this chapter are:



Package Contents (Page

)



Unpacking (Page

)



Required Equipment and Software (Page

)



Computer Setup (Page

)



Management Methods and Protocols (Page

)



Default IP (Page

)



)



Setting the initial IP address (Page

)

Package Contents

When you unpack the product package, you will find the items listed below. Please inspect
the contents, and report any apparent damage or missing items immediately to your
authorized reseller.



This Management Switch



User’s Manual



External power adapter

Unpacking

Follow these steps to unpack the EX24000 Switch and prepare it for operation:

Open the shipping container and carefully remove the contents.

Return all packing materials to the shipping container and save it.

Confirm that all items listed in the "Package Contents" section are included in

the shipment. Check each item for damage. If any item is damaged or missing, notify
your authorized EtherWAN representative.

Summary of Contents for EX24000
















































































































































































































































Search results

Summary of Contents for EX24000

Reviews:

Brands by name

Popular brands

EtherWAN EX24000, User Manual

Search results

Summary of Contents for EX24000

Reviews:

Brands by name

Popular brands