EtherWAN EX24000 User Manual Download Page 19

Page: 19 / 239

Required Equipment and Software

The following hardware and software are needed in order to manage the switch from the
web interface:



Computer with an Ethernet Interface (RJ-45)

Managing the switch requires a personal computer (PC) or notebook computer

equipped with a 10/100base-TX Ethernet interface and a physical RJ-45

connection. The preferred operating system for the computer is Microsoft Windows

XP/Vista/7. It is possible to use Apple OSX or Linux systems as well, but, for the

sake of brevity, all web configurations in this manual will be shown using Windows

7 as the underlying operating system.



Cat 5+ Ethernet Cables

An Ethernet cable of at least Category 5 rating is required to connect your

computer to the switch. The cable can be configured as “straight-through” or

crossover.



TFTP Server Software

Trivial file transfer protocol (TFTP) server software is needed to update the switch

firmware and to upload/download configuration files to the switch. Users not

performing these tasks do not need TFTP software installed. Several good TFTP

servers are available for free online. The server that will be used in this manual is

TFTPD32 by Philippe Jounin.



Web Browser Software

The end user can employ any of the following web browsers during switch

configuration: Internet Explorer, Firefox, or Chrome. Internet Explorer is the

preferred browser for EtherWAN switch configuration. If there is trouble with other

browsers while attempting to program the switch, Internet Explorer should be used.

EX24000 Switch Users Guide

Summary of Contents for EX24000
















































































































































































































































Search results

Summary of Contents for EX24000

Reviews:

Related manuals for EX24000

Brands by name

Popular brands

EtherWAN EX24000, User Manual

Search results

Summary of Contents for EX24000

Reviews:

Related manuals for EX24000

Brands by name

Popular brands