etex Promat PROMAFOUR boards How-To Download Page 4

Page: 4 / 13

Promat

| How to Line a masonry fireplace

TECHNICAL SERVICES EMAIL:

[email protected]

PROMAFOUR® boards

are

mechanically strong and easy

to work with.

Board dimensions are

2500mm x 1250mm and

1250mm x 1250mm

Available in thicknesses of

12mm and 15mm.

PROMAFOUR® GLUE 1000

a refractory silicate based glue

which resists to temperatures

up to 1000°C.

Available in 310ml cartridges.

PROMAFOUR® GLUE 1000

PROMAFOUR® Primer

is a

non-combustible and vapour

permeable primer, which

has been designed for use

at elevated temperatures.

Available in 3 Litre and

1 Litre tubs.

PROMAFOUR® Primer

PROMAFOUR® HT

Joint Filler

for finishing.

Available in 1.5kg tub

Getting started

Equipment required

Promat PROMASEAL®

SILICONE SEALANT

is a

silicone based fire protection

sealant.

Available in white or grey

colour.

OTHER ITEMS YOU MAY NEED

• Dust and Plastic

Sheeting/Matting

• Appropriate PPE – Glasses,

gloves, dust masks

• Countersunk wood screws

and metal plugs

•  Spatula
•  Hand Saw
•  Sponge
•   Right angle / set square
•  Nail Gun
•  Spirit level
•   Knee pads / air masks

with filters

• A circular saw or jigsaw with

dust extraction device or with

separate dust extraction

(The one seen in this guide is

a Festool Plunge Saw with dust

extractor) other plunge saws

are available

• Cutting Table
• Hand saw (If required for

shaving boards to fit)

• Buckets ( for mixing

compounds)

• Cleaning spatula to wipe the

excess glue off before it sets

• If Painting – Paint and roller
• Countersunk concrete/

masonry screws

BEFORE YOU BEGIN

Before you begin to install

your PROMAFOUR® lining it

is important to carefully read

the following safety measures

and instructions;
• Always observe the safety

instructions of the stove

manufacturer

• Always ensure safe working

conditions and a safe

working environment

• Take the necessary

precautionary measures

to prevent possible injuries

• Always use the correct

equipment as described

in this installation

manual and stove

manufacturers guidelines.

This is not a guide on how to

install a stove – please ensure

you meet building regulations

and follow all of the procedures

for the stove installation in

addition to this process.

Summary of Contents for Promat PROMAFOUR boards














Search results

Summary of Contents for Promat PROMAFOUR boards

Reviews:

Related manuals for Promat PROMAFOUR boards

Brands by name

Popular brands

etex Promat PROMAFOUR boards, How-To

Search results

Summary of Contents for Promat PROMAFOUR boards

Reviews:

Related manuals for Promat PROMAFOUR boards

Brands by name

Popular brands