MIX-N-GO - User Manual Rev 5.2
Page 22 of 41
B) Unloading through the rear discharge hole without flexible pipe.
•
With the bucket in unloading position (loading mouth facing upwards), operate the discharge
hole cylinder by means of the control lever hydraulically connected to the cylinder.
•
Start auger rotation to help discharge the material.
•
To operate the discharge hole cylinder: press the button in the cab to energize the magnet of the
electro-hydraulic switch; operate the bucket hydraulic control to open or close the discharge
hole.
IMPORTANT -
While operating the lever, hold the button down.
Release the button to de-energize the magnet and restore the forward rotation. This will cause the
material to be pushed outwards through the discharge hole.
IMPORTANT
- During the cylinder opening/closing phase, the rotation of the mixing shaft stops.
C) Unloading through the rear discharge hole with flexible pipe
DANGER
- Before connecting the flexible pipe, make sure the machine is parked in a stable position
and no one can operate the controls.
DANGER
- The discharge pipe shall be connected by a second operator who shall keep at a safe
distance and start connection only once the machine has been parked and the parking brake or other
parking device has been engaged. To install the discharge pipe, obey the following instructions:
Machine Operator: Raise the bucket 4 feet above the ground with the mouth parallel to the ground.
Stop the engine and ensure no one can operate the machine controls.
Operator on the ground: If the load is suspended, place two supports to the sides of the bucket or install
the flexible pipe with the bucket resting on some supports on the ground.
Connect the 2 hooks at the top of the pipe to the special pins located on the equipment, near th
discharge hole.
DANGER -
Do not stand under the bucket while securing the pipe and while discharging the mix. D)
Unloading through the discharge spout of the lateral discharge hole
DANGER -
Before connecting the spout, make sure the machine is parked in a stable position and no
one can operate the controls.
DANGER -
The discharge spout shall be connected by a second operator who shall keep at a safe
distance and start connection only once the machine has been parked and the parking brake or other
parking device has been engaged. To install the discharge spout, obey the following instructions:
Machine operator: Raise the bucket 4 feet above the ground. Stop the engine and ensure no one can
operate the machine controls.
Operator on the ground:
If the load is suspended, place two supports to the sides of the bucket or install the spout with the bucket
resting on some supports on the ground.
Summary of Contents for MIX-N-GO BMX-100
