background image

 

9/9

Note

1) Please consult our sales representatives or engineers before using our products listed in this

manual for applications requiring especially high reliability what defects might directly cause

damage to other party’s life, body or property (listed below) or for other applications not specified

in this manual.

1. Aircraft equipment

2. Aerospace equipment

3. Undersea equipment

4. Medical equipment

5. Traffic signal equipment

6. Disaster prevention / crime prevention equipment

7. Data-processing equipment

8. Applications of similar complexity or with reliability requirements comparable to the

applications listed in the above.

2) Product specifications in this manual are as of 4.April .2000 and are subject to change or stop the

supply without notice. Please confirm the specification before ordering any product. If there are

any questions, please contact our sales representatives or engineers.

3) The categories and specifications in this manual are for information only. Please confirm detailed

specifications by checking the product specification document or requesting for the approval

sheet for product specification, before ordering.

www.DataSheet4U.com

Summary of Contents for ENV-05F-03











Reviews: