background image

Product Specifications

Page 16

Product Specifications

Carbon Dioxide

Technology: Ultra Low Power, LED based NDIR

Measurement Range: 0-2000 ppm

Accuracy: ± 50ppm

Altitude/Pressure Compensation: Built-in correction

Self-Calibration: Automatic Background Calibration

Resolution: 1 data byte (0-200 decimal), 10 ppm

Temperature

Range: 0ºC to 51ºC (32ºF to 124ºF)

Accuracy: ± 0.3ºC (± 0.5ºF)

Resolution: 1 data byte (0-255 decimal), 0.2ºC (0.36ºF)

Relative Humidity

Range: 0% to 100% RH

Accuracy: ±3% RH…10-90%, ±7%... 0-10%, 90-100%

Resolution: 1 data byte (0-200 decimal), 0.5%

Power Supply

Type: Integrated Solar Panel

Operational Light Levels: 50 lux

Minimum Charge Time before Operation: 10 min @ 200 lux

Charging Light Level: 200 lux

Maintain Operating Life Level: 200 lux for 6 hours

Maximum Charge Time: 16 hours @ 200 lux

Operating Life From Full Charge: 72 hrs @ 0.0 lux

Battery: for backup, start assist & test mode (supplied). Use high quality 
CR2032 coin cell. The battery will typically provide 5 years operating life 
in zero light conditions.

General

Weight: 115 g, (4 oz)

Mounting: screws or double sided tape (not included)

Summary of Contents for echoflex RCT






















Reviews: