ETC ArcSystem Pro D4 Series Installation Manual Download Page 7 | Manualshive

Page: 7 / 68

ETC ArcSystem Pro D4 Series Installation Manual Download Page 7

Introduction

1

Introduction

Congratulations on your purchase of ArcSystem products. ArcSystem is a family of overhead LED
products designed for installations where dimming, light quality, and ease of installation are
absolutely essential. With ArcSystem, you will experience perfectly smooth dimming from 100%
down to absolute zero. ArcSystem luminaires come in a variety of form factors, beam angles,
and color-temperature options, all with high-efficiency optics and an outstanding quality of light
ideal for any application.

ArcSystem products with ArcMesh can be controlled using wired DMX or the wireless ArcMesh
protocol. ArcSystem products without ArcMesh can be configured for RDM control. This manual
provides step by step instruction on the installation of ArcSystem Pro One-Cell luminaires, D4
Series Drivers, and full system integration. For information on installing ArcSystem Pro D1 and
D2 Series Drivers, see

the ArcSystem D1 and D2 Series Drivers Installation Guide

at

etcconnect.com/ArcSystem

. For information on ArcSystem Pro Multi-Cell luminaires, see the

ArcSystem Pro Installation Manual

and the

ArcSystem Pro Multi-Cell RDM Installation Guide

at

etcconnect.com/ArcSystem

All ETC manuals are available for download free of charge at

Document Conventions

This document uses the following conventions to draw your attention to important information.

Note:

Notes are helpful hints and information that is supplemental to the main text.

CAUTION:

A Caution statement indicates situations where there may be

undefined or unwanted consequences of an action, potential for data loss or
an equipment problem.

WARNING:

A Warning statement indicates situations where damage may

occur, people may be harmed, or there are serious or dangerous
consequences of an action.

WARNING:

RISK OF ELECTRIC SHOCK! This warning statement indicates

situations where there is a risk of electric shock.

All ETC documents are available for free download from our website:

.

Please email comments about this manual to:

[email protected]

.

«
...
5
6
7
8
9
...
»

Summary of Contents for ArcSystem Pro D4 Series





































































Reviews:

No comments