manualshive.com logo in svg

ETC ArcSystem Pro D4 Series, Installation Manual, Page: 21 / 68

Share
Download
ETC ArcSystem Pro D4 Series Installation Manual Download Page 21

D4 Series Wall-Mount Driver Installation

15

D4 Series Wall-Mount Driver Installation

This section provides information on how to install wall-mount D4 Series constant current
(CC) and constant voltage (CV) drivers. The D4 Constant Current Driver can control up to four
ArcSystem Pro One-Cell or Pro One-Cell Small luminaires. Up to 32 drivers can be installed on
one hard-wired line of DMX.

Electrical and Wiring Specification

WARNING:

Circuits that are installed without an accessible power

disconnect device cannot be serviced or operated safely.

AVERTISSEMENT :

Il est imprudent d'utiliser ou de réparer les circuits

installés sans qu'un dispositif de déconnexion de l'alimentation ne soit
accessible.

Install the D4 Driver on a power distribution system with reliably identified earthed neutral and
install a maximum 15 A circuit breaker on the line conductor.

ETC recommends installing all wiring to and from wall-mount drivers in grounded metal conduit.

The wall-mount D4 Driver accepts 100–277 VAC (150 models) or 100–240 VAC (350 and 700
models), 50/60 Hz. Emergency models only: requires normal sense and maintained (emergency)
input power.

Summary of Contents for ArcSystem Pro D4 Series





































































Reviews:

No comments