Water hardness
Ratio of tap water : distilled water (pH = 7)
medium
2 : 1
hard
1 : 1
very hard
1 : 2
Sprinkling appliance (additional spray)
It is used for moistening fabrics and it is effective in ironing extremely creased fabrics. It is
activated by repeated pressing of additional spray button
E
. We do not recommend applying
additional spray for fine fabrics (e.g.
silk and synthetic
) as the used water may stain the fabric.
Intensive steaming (steam shock)
Use only if the steam ironing is insufficient. In this case press steam shock button
F
several
times (Fig. 6A
). Thus you will get additional steam except for the steam created by
standard steaming.
WARNING
When you press intensive steaming button
F
several times, water may drip from the ironing
plate due to excess water in the steam chamber. Do not consider this as faulty operation.
!
VERTICAL SYSTEM
It is intensive vertical steaming for steaming of freely hanging textiles (such as hanging clothes,
draperies, hangings). Using control
H
set one of the programs for steamig. Reaching the
required temperature is shown on the display and announced by sound signaling. Stretch the
fabric slightly with one hand and move the iron vertically bottom-up (Fig. 6B
). Press the
intensive steaming button
F
so that you reach vertical steam hammer. Do not hold the intensive
steaming button pressed continuously and do not use it more than 10 times consecutively.
WARNING
– Use the VERTICAL function only if the programs
COTTON
,
JEANS
or
LINEN
are set.
– Prevent burning of sensitive fabrics, do not close them to the iron to distance of 10 to 20 cm.
!
DRIP STOP
The appliance prevents leaking water from the ironing plate when its temperature is insufficient.
Self-cleaning system (SELF CLEAN)
Hold the iron disconnected from power supply in your hand, turn steaming regulator
D
to
0
position (Fig. 5) and lift off cover
C
to open the filling container lid. Pour water into container
I using the enclosed cup
O
to fill half of it and close the filling hole lid (Fig. 4) by snapping it.
Keep the position of the iron for pouring water in it
. Put the iron to the rest position
(Fig. 7) and set the regulation wheel
H
to the program LINEN. Plug power cord
M
into
a socket. When you hear a sound signal (indicating reached selected temperature), disconnect
the iron from the electric power. Hold the iron in the horizontal position over a sink. Press the
SELF CLEAN
button repeatedly (two to three times), each time for about 5 seconds. Then
wait till water stops going out from the ironing plate. If the iron still contains a lot of impurities,
repeat the procedure while pushing the intensive steaming button between individual pushing
of the
SELF-CLEAN
button. After completing the cleaning, plug the iron into the electric power,
set the selected program and then iron a clean piece of cotton cloth so that the ironing plate is
cleaned.
Clean the ironing plate using the SELF CLEAN function continuously.
28
GB
/ 74
Summary of Contents for DIGI VIENTO 7284
