background image

7

user manual LokPilot mfx (61600) V1.0 04/2005

CV Name

Description

Range

Factory value

1

Address

address of locomotive

01 – 80

03

2

Starting voltage

determines the starting speed

01 – 63

18

3

Acceleration

This value multiplied by 0.25 gives the time

01  –  63

16

from stop to maximum speed

4

Deceleration

This value multiplied by 0.869 gives the time

01  –  63

12

from maximum speed to stop

5

Maximum speed

maximum speed of locomotive

01 – 63

63

6

Medium speed

Speed of locomotive at medium speed step

0 - 64

22

7

Version number

Internal software version of LokPilotDCC (read only)

- -

8

Factory  reset

Resets decoder to default settings

8

Writing value 8 triggers a reset of all CVs to factory values

53 Load control

Parameter 1 (control reference)

01 - 63

35

parameter 1

Determines the back EMF voltage that the motor
should supply at maximum speed. The more efficient
the motor, the higher this value may be. Reduce
this value if the engine does not reach its designed
maximum speed.

54 Load control

Parameter 2 („K“-component) of the internal PI-controller. 01 - 63

24

parameter 2

Determines how strongly load control effects.
The higher the value, the stronger the decoder
controls the motor.

55 Load control

Parameter 3 („I“-component)

10 - 63

24

The momentum of the motor determines parameter 3.
Motors with large flywheels or large diameter require
a smaller value.

56 Load control influence Determines how strongly load control is active.

01 - 63

63

78

Starting voltage in analogue AC mode

01 - 63

25

79

Maximum speed in analogue AC mode

01 - 63

63

Summary of Contents for LokPilot mfx









Reviews: