background image

11

PROBLEM:

 The video not being saved to the memory card.

SOLUTION:

 (1) Always stop the video recording function and power off the 

battery first. After this you can take out the memory card. (2) Always turn off the 
power to the Transmitter before inserting or removing the memory card.

PROBLEM:

 Why is it that when I record video, the memory card only records 

videos of 75MB total but the file size remains 175MB?

SOLUTION:

 When the memory card is properly formatted in the transmitter, 

the formatting will split the file to speed up recording and smooth out playback. 
Therefore it shows a smaller file size when its properties are shown on a computer 
screen. The memory card is full when the LCD screen on the transmitter displays 
“Full”. It’s worth noting that when the memory card is formatted in the transmitter, 
you must reformat it if you intend to use it in another device. First save any files to 
your computer before formatting the card.

REPLACEMENT PARTS

ESTE4556 BODY 

SET

ESTE4557 

ROTOR BLADE SET (4)

ESTE4558 

MOTOR HOLDER SET (4)

ESTE4559 

RUBBER LAND GEAR (4)

ESTE4560 

SCREW SET (4)

ESTE4561 MAIN 

PCB

ESTE4562 CAMERA
ESTE4563 5.8G 

ANTENNA

ESTE4564 

MOTOR SET (4)

ESTE4565 

USB CHARGE CORD

ESTE4566 

LIPO 1S 3.7V 650

ESTE4567 ROTOR 

BLADE 

WRENCH 

Summary of Contents for Proto-X FPV













Reviews: