Esteam e1200 Owner'S Manual Download Page 22

 

21 

(vii)  No warranty is provided as to failure of any cosmetic item or finish, labeling, silk 

screening, decals, paint, trim or other similar decorative items. 

 

(viii)  Brass, rubber and synthetic rubber parts (e.g. "O" rings, diaphragms, gaskets, 

seals, grommets) are considered expendable in normal use, and are therefore 

not included in any warranty by Esteam. 

                  

                        PART IV - EXCLUSION OF LIABILITY 

 

Esteam makes no warranties or representations, either expressed or implied, oral or 

written, in fact, or by operation of law, or otherwise, except as expressly stated herein 

as to the 90 day Limited, 12 month and Lifetime Extended warranties. Esteam, its 

officers, directors, agents, dealers and its affiliates (and their respective officers, 

directors, agents and dealers) shall not be liable to the customer nor to any party for any 

liability, including without limitation, strict liability, liability for loss, injury or damage due 

directly or indirectly to the use or operation of the Esteam product; consequential, 

exemplary and/or punitive damage or loss, whether in contract, tort, or otherwise. 

                        

                        PART V - RETURN GUIDELINES 

  

Defective items must be replaced through a local Esteam Distributor. Replacement 

parts will be sent via prepaid regular ground service to the distributor. The defective part 

must be returned F.O.B. factory within 30 days including a letter providing the machine's 

serial number, date of purchase, material return authorization number, and customer 

name. If applicable, credit will be issued after the item has been evaluated by Esteam. 

Failure to comply with return policy will void the warranty on that item. 

 

                          PART VI - CREDIT POLICY 

 

All customers purchasing parts through an Esteam distributor must arrange credit 

directly with that distributor. 

            

                         PART VII - OUTSIDE SOURCE WARRANTY REPAIRS 

 

At the sole discretion of Esteam, it may be necessary to perform warranty/repairs at an 

outside source. An estimate must be submitted to and approved by Esteam prior to 

work being performed. Failure to do so will result in denial of your warranty claim. 

 

              

PART VIII - TRANSFERABILITY 

 

This warranty is not transferable to any subsequent owner. 

 

                        PART IX - NOTICE - CUSTOMER OBLIGATIONS 

(i) 

Your responsibility as a customer includes but is not limited to cleaning, 

lubricating, seasonal maintenance (e.g. winterizing), replacement of worn parts 

and all regular scheduled or unscheduled maintenance. 

Summary of Contents for e1200

































Reviews: