EST 270219 R1 Installation Manual Download

Page: 22 / 24

ATPC

Manual

SDR32K

PO1-1 Control ARA relay activity to ATP

SDR32K

PO1-2 Control ARA relay for back-up AMP power

SDR32K

PO1-3 Control ARA relay for riser “A” transfer

SDR32K

PO1-4 Control ARA relay for riser “B” transfer

SDR32K

PO1-5 Control ARA relay for riser “C” transfer

SDR32K

PO1-6 Control ARA relay for riser “D” transfer

Dual-Channel 360 Watts Active (180 Watts
Per Channel), 180 Watts Back-Up

Note:

Refer to single channel 360 watts active, 180 watts back-up,

drawing on page 14 for amplifier installation. Same setup applies for
both single and dual channel.

Components

Quantity Component Part

Number Comment

SAN-CPU

P/N 130125

Control for amplifier rack

SIN-16

P/N 240158

TB1-1 Monitor ATP #1 for trouble

SIN-16

TB1-2 Monitor ATP #1 for power fail

SDR32K

P/N 240181

Control for relays

ARM-8

P/N 240122

Relay for 24 VDC power to ATP activity relay

ARA Relay

P/N 250055

Relay for back-up AMP power transfer

ARA Relay

P/N 250055

Relay for riser “A” switch over

ARA Relay

P/N 250055

Relay for riser “B” switch over

ARA Relay

P/N 250055

Relay for pre-amp switch to back-up

SDR32K

PO1-1 Control ARA relay activity to ATP

SDR32K

PO1-2 Control ARA relay for back-up AMP power

SDR32K

PO1-3 Control ARA relay for riser “A” transfer

SDR32K

PO1-4 Control ARA relay for riser “B” transfer

SDR32K

PO1-5 Control ARA relay for riser “C” transfer

Dual-Channel 720 Watts Active (360 Watts
Per Channel), 180 Watts Back-Up

Note:

Refer to single channel 720 watts active, 180 watts back-up,

drawing on page 16 for amplifier installation. Same setup applies for
both single and dual channel.

Components

Quantity Component Part

Number Comment

SAN-CPU

P/N 130125

Control for amplifier rack

SIN-16

P/N 240158

TB1-1 Monitor ATP #1 for trouble

SIN-16

TB1-2 Monitor ATP #1 for power fail

SIN-16

TB1-3 Monitor ATP #2 for power fail

SIN-16

TB1-4 Monitor ATP #2 for power fail

SDR32K

P/N 240181

Control for relays

ARM-8

P/N 240122

Relay for 24 VDC power to ATP activity relay

ARA Relay

P/N 250055

Relay for back-up AMP power transfer

ARA Relay

P/N 250055

Relay for riser “A” switch over

ARA Relay

P/N 250055

Relay for riser “B” switch over

ARA Relay

P/N 250055

Relay for riser “C” switch over

ARA Relay

P/N 250055

Relay for riser “D” switch over

ARA Relay

P/N 250055

Relay for pre-amp switch to back-up

SDR32K

PO1-1 Control ARA relay activity to ATP

firealarmresources.com

Summary of Contents for 270219 R1

























Search results

Summary of Contents for 270219 R1

Reviews:

Related manuals for 270219 R1

Brands by name

Popular brands

EST 270219 R1, Installation Manual

Search results

Summary of Contents for 270219 R1

Reviews:

Related manuals for 270219 R1

Brands by name

Popular brands