EST 270219 R1 Installation Manual Download Page 18

Page: 18 / 24

ATPC

Manual

Amplifier Installation Application Drawings

Single-Channel, 180 Watts Active, 180
Watts Back-Up

LOUVERED BLANK

BATTERY PACKS

LOUVERED BLANK

BLANK

ARM8 SDR-32K SIN-16

SAN-CPU

BLANK

CHASSIS PLATE

SAN MODULES

250 WATT DUKANE

AMP BACKUP

250 WATT DUKANE

AMP BACKUP

250 WATT DUKANE

AMP RISER A

250 WATT DUKANE

AMP RISER A

AMPLIFIER TERMINAL

PANEL #1

AMPLIFIER TERMINAL

PANEL #1

3.50"

42.00"

5.25"

1.75"

10.00"

.25"

RUWA200-42, Front View

RUWA200-42, Rear View

TOTAL

EACH SIDE

[ATPC-010.CDR]

•  Locked door on rear of rack.
•  DO NOT install door on rack front.
•  Spacing is required for air flow so amps will not overheat.
•  Battery back-up sits on the bottom of rack behind the blanks.

Components

Quantity Component Part

Number Comment

SAN-CPU

P/N 130125

Control for amplifier rack

SIN-16

P/N 240158

TB1-1 Monitor ATP #1 for trouble

SIN-16

TB1-2 Monitor ATP #1 for power fail

SDR32K

P/N 240181

Control for relays

ARM-8

P/N 240122

Relay for 24 VDC power to ATP activity relay

ARA Relay

P/N 250055

Relay for back-up AMP power transfer

ARA Relay

P/N 250055

Relay for riser “A” switch over

SDR32K

PO1-1 Control ARA relay activity to ATP

SDR32K

PO1-2 Control ARA relay for back-up AMP power

SDR32K

PO1-3 Control ARA relay for riser “A” transfer

firealarmresources.com

Summary of Contents for 270219 R1

























Search results

Summary of Contents for 270219 R1

Reviews:

Brands by name

Popular brands

EST 270219 R1, Installation Manual

Search results

Summary of Contents for 270219 R1

Reviews:

Brands by name

Popular brands