background image

 

4

SAFETY INFORMATION                                                                                                       

Please read and understand this entire manual before attempting to assemble, operate 
or install the product. If you have any questions regarding the product, please call 
customer service at: 1-855-CHANT-US (1-855-242-6887) from 8:00 am to 5:00 pm 
Eastern time, Monday to Friday. 
1.

 

CALIFORNIA PROPOSITION 65 WARNING:   
(a)

 

Combustion by-products produced when using this product contain chemicals 
known to State of California to cause cancer, birth defects and other 
reproductive harm. 

(b)

 

Handling the brass material on this product exposes you to lead, a chemical 
known to the state of California to cause cancer and birth defects or other 
reproductive harm. Wash hands after handling. 

2. 

The installation must conform with local codes or, in the absence of local codes, 
with the 

National Fuel Gas Code, ANSI Z223.1 /NFPA 54, Natural Gas and 

Propane Installation Code, CSA B149.1, or Propane Storage and Handling 
Code, B149.2.

     

3. 

Minimum clearance to the combustible materials is 44 inches. 

4. 

Perform a leak test with a soapy solution: 

(a)

 

To check gas connections. 

(b)

 

After connecting a new cylinder. 

(c)

 

Upon re-assembly after disassembly. 

Please refer to the leak test procedure indicated in this instruction manual on page 
15. 
Replace the hose assembly prior to the appliance being put into operation if there 
is evidence of excessive abrasion or wear, or if the hose is damaged.

 

The pressure 

regulator and hose assembly supplied with the appliance must be used .The 
replacement hose assembly/ regulator shall be that specified by the manufacturer. 

5. 

If you don’t feel the heater is on a stable surface, use a ground screw to fix the base 
of the heater on the surface where the heater is installed. Fix the base on an incline 
no wider than 15 degrees. 

6. 

Place the propane hose with regulator assembly out of pathways where people may 
trip over it or in areas where the hose will not be subjected to accidental damage. 

7. 

This heater is equipped with a battery-operated ignition device; please refer to the 
assembly instructions on page 14. 

8. 

Materials or items when stored under the heater will be subjected to intense heat 
and could be seriously damaged. 

9. 

Clothing or other flammable materials should not be hung on  the heater, or 
placed on, under or near the heater . 

10. 

Children and adults should be alerted to the hazards of high surface temperatures 
and should stay away to avoid burns or clothing ignition. 

11. 

Young children should be carefully supervised when they are in the area of the 
heater. 

12. 

Any guard or other protective device removed for servicing the heater must be 
replaced prior to operating the heater. 

 

Summary of Contents for 640-08477458-7




















Reviews: