background image

ET288/ET388

18

Before contacting your dealer for aid, please review the following information. It may save you
both time and expense. This list includes common problems that may not be covered under the
treadmill s warranty.

PROBLEM                                                                    

SOLUTION/CAUSE

Display does not light

                          Tether cord not in position.

Circuit breaker on front grill tripped. Push circuit breaker in until
it locks.
Plug is disconnected. Make sure plug is firmly pushed into the
AC household wall outlet.
Household circuit breaker may be tripped.
Treadmill defect. Contact your Spirit dealer.

Treadmill belt does not stay centered

Treadmill belt hesitates when walked/run on

      A user may be walking while favoring or putting more weight on

either the left or right foot. If this walking pattern is natural, track
the belt slightly off-center to the side opposite from the belt
movement. See General Maintenance section on Treadmill belt
Tension. Adjust as necessary.

Motor is not responsive / Display is lit

Make certain clock is running. If it is then service may be
Needed.

Treadmill will only achieve approximately

7 mph but shows higher speed on display

       This indicates motor should be receiving power to

operate. Low AC voltage to treadmill. Do not use an extension
cord. If an extension cord is required it should be as short as
possible and heavy duty 16 gauge minimum. Low household
voltage. Contact an electrician or your Spirit dealer. A minimum
of 110 volt AC current is required.

Treadmill belt stops quickly/suddenly when

High belt/deck friction. See General Maintenance

tether cord is pulled

section on lubrication.

Treadmill trips on board 15 amp circuit

           High belt/deck friction. See Belt/deck lubrication procedure

Computer shuts off when console is

touched (on a cold day)while walking/running

Treadmill is not grounded. Static electricity is  crashing  the

computer. Refer to Grounding Instructions on page 4.

ERROR MESSAGES:

1.

LS:

     The treadmill hasn t received a speed signal for 8 seconds.

2.

 E1:

    Console memory malfunction or CPU problem.

3.

E2:

Incline position error

Service Checklist - Diagnosis Guide

Summary of Contents for ET 288





















Reviews: