background image

EsiWelma Srl 

URD20SL_en.doc - rev. 0 

CO

2

 gas detectors – URD20SL 

24/09/2010 

Gas detection systems for industrial environments 

2/8

 

Technical 
characteristics 

 

Type of sensor 

NDIR (nondispersive infrared) 

Detectable Gas 

Carbon dioxide (CO

2

Power supply 

11÷28Vdc 

Max power consumption 

3.2W 

Measuring range  

0...20,000 ppm 

Precision 

±

 5% full scale, 

±

 10% readout 

Repeatability 

±

 5% full scale, 

±

 10% readout 

Measurement resolution 

20 ppm 

Microprocessor resolution 

1024 points (10 bit) 

Digital filter system 

Kalman Filter 

Watchdog Internal 
Warm-up time 

< 2m 

Stabilization time 

< 2m 

Response time 

< 25s (T90) 

Average Sensor life (in air) 

255 weeks 

4..20mA Output 

Proportional mode 
(default) 

 

Consumption mode 
(applications at 1 or 2 
thresholds) 
 

 

4…20mA Output reference 
selection: 

 
-  4mA    = 0 ppm 
- 20mA   = 20000 ppm 

 

-   0mA   = no alarm 
- 10mA   = 1

st

  threshold alarm 

- 20mA   = 2

nd

  threshold alarm 

 

 
 
by jumper selectable polarity 

4…20mA output load resistor 

- up to 200

 at 12Vdc power supply 

- 200

 

÷

 700

 at 24Vdc power supply 

Operating Temperature 
Storage Temperature

 

-20 

÷

 50 °C 

-20 

÷

 70 °C

 

Relative Humidity 

(without condensing)

Operation 

Storage 

 

 

15 

÷

 90 %RH 

45 

÷

 75 %RH

 

Operating pressure (KPa) 

80 

÷

 110 

Air speed (m/s) 

 6 

Visual warnings 

Red LED visible with detector energised 

Dimensions and weight 

See dedicated section 

Options & Accessories 

 

Card with 4 SPDT relays 

UZR20.4

 

NO or NC contacts available, 
jumper selectable 

See threshold limit settings

  

 

Maximum relay capacity: 

50mA at 24Vac/dc, 100mA at 12Vac/dc 

Relay operating mode: 

direct: relay ON when an event is 
detected 

reverse: relay ON when no event is 
detected 

TUL40..

 Gas calibration kit 

See installation and commissioning chapter

 

TUS40   

Handheld terminal   

for service and maintenance  

See installation and commissioning chapter 

CRG40

   Gas collecting cone 

See dedicated data sheet 

PAP40

   Powerful jets protection 

See dedicated data sheet 

 

 
EC Conformity 
EMC Directives / Standards 
 
 
LVD Directives / Standards 

 
 
Electromagnetic Compatibility Directive 
EMC 2004/108/EC, Standard EN50270 
 
Not applicable 
 

Summary of Contents for Sensigas URD20SL









Reviews: