manualshive.com logo in svg

Escea AF series, Installation And Service Instructions Manual, Page: 48 / 58

Share
Download
Escea AF series Installation And Service Instructions Manual Download Page 48

B

AC

D

E

F

G

SER

VICE

48

G5 Flue 

Installation

The freestanding unit and flue system should be installed prior to the AF-Series fireplace being 
installed (for horizontal termination for FS730: see next page, section G6).

Place the freestanding unit in the correct 

location, complying with 
the clearances specified in the previous 
section.

Remove 2 screws on each side of the fas-

cia just below the top panel and pull towards 
you to remove the fascia.

 Fix the FS730 unit to the floor using the 

four securing holes in each corner of the unit.

 Refer to Section B3 for flexi flue and 

converter box clearances.
 

Refer to section C of this installation 

manual for minimum and maximum flue 
lengths, restrictor settings for your installa-
tion, and all other flue information.  

Run the black Ø230mm flue liner lengths 

from the top of the freestanding unit until it 
penetrates the Ø265mm ceiling hole.

Use the supplied Ceiling plate for 

tidying the internal termination point of the 
Ø230mm flue liner. 

Run the 2x flexible flues down through the 

Ø230mm flue liner and attach it to the Flue 
Spigot Plate as per section C of this manual

Open the flue liner rodent guard and close 

around the flexi flue. Rivet, screw or cable 
tie the open end to prevent it from opening. 
Bend the two perpendicular tabs down and 
screw into the flue liner using a short self 
tapping screw. 

Note

: Take care when installing 

the rodent guard to not cause damage to the 
flexi flue.

Install flue termination as per section C of this manual

Note: Ensure a power supply is within 1m of the rear of the appliance.

Ceiling Ring

225mm
Flue liner

2x Flexible
flue inner

Coaxial to Colinear
conversion box

Duravent 4x6”
Rigid Direct-vent
flue

Rigid flue

Flexible flue clamped
to Flue Spigot Plate

AF700
Fireplace

FS730 Freestanding
Unit

Flue Liner
Rodent Guard

Ø265 mm
Ceiling hole

Summary of Contents for AF series



























































Reviews:

No comments