6
TOOLS REQUIRED FOR THE FOLLOWING STEPS
1 - 15/16" Open end Wrench
1 - 15/16” Socket and Ratchet (optional)
1 - 9/16” Deep Well Socket & Ratchet
1 - 3/4” Socket & Ratchet
1 - 3/4” Open end Wrench
1 - Phillips Screwdriver
1 - Level
1 - Tape Measure
1 - Rubber Mallet
1 - Set of Padded
Saw Horses
1 - 9/16” Open end Wrench
1 - Cordless drill & 9/64” drill bit
1 - 5/16” socket driver (for cordless drill)
1 - Safety glasses
1 - Ladder
ASSEMBLY INSTRUCTIONS (Day 5)
Figure 3B
Figure 3A
NOTCHES IN BASE
PLATE MUST BE ON
SIDE AS SHOWN
FRONT
BACK
SIDE
Be sure that the
“Back Side”
stickers are at the
back of the poles.
BACK SIDE
PIECE OF
CARDBOARD
Must be at least as
big as pole base plate.
FAILURE TO FULL
Y ENGAGE THE
BOTTOM OF THE UPPER POLE TO
THE 6” MARK ON THIS BOTTOM
POLE STICKER, COULD CAUSE
YOUR UNIT TO COLLAPSE AND MAY
RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE.
BACKSIDE
Bottom
of
upper
pole
must
cover
the
above
orange
portion
of
this
sticker
(6” mark).
WARNING
!
4L-8151-00
FAILURE TO FULLY ENGAGE THE
BOTTOM OF THE UPPER POLE TO
THE 6” MARK ON THIS BOTTOM
POLE STICKER, COULD CAUSE
YOUR UNIT TO COLLAPSE AND MAY
RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE.
BACKSIDE
Bottom of upper pole must cover the
above orange portion of this sticker
(6” mark).
WARNING
!
4L-8151-00
NOTE
: Top Pole must cover upper
orange area of sticker. If Pole goes
slightly past the 6” mark, it is OK
.
1.
Before putting any of the poles tubes together, make sure that the orange area
of the Warning Sticker on Pole (#2) is 6 inches from the top end.
Be sure that
the “Back Side” stickers are at the back of the pole.
See
Figure 3A.
WARNING: This pole assembly is heavy. Step 2 will require two adults.
Make sure you can control the pole when slamming it together. Have a
helper stand on the opposite side of the pole. Attention should be paid
to one’s feet and toes during entire slamming process.
Align the upper pole (#3) with the bottom pole (#2) as shown in
Figure 3A
and
slide them together. While maintaining control of the pole assembly stand poles
up
STRAIGHT
on a piece of cardboard from your box,
lift poles up by bottom
pole
below the 6” mark shown on sticker and slam down the bottom pole as
many times as needed on the cardboard
until the bottom of the upper pole
reaches the 6”
mark (on Sticker) on the bottom pole. Lift the pole 10-12 inches
off the ground when slamming the poles together.
See Figure 3A & 3B
.
Should any concerns exist about damaging your driveway, use a 12” X 12” piece
of Plywood or mdf board.
NOTE:
When slamming poles together make sure to keep the poles
STRAIGHT.
Slamming the poles down crooked will damage the bottom of
the pole and base plate. Top Pole must cover upper orange area of sticker.
If Pole goes slightly past the 6” mark, it is OK.
IMPORTANT! DO NOT hit poles with hammer or sledge hammer
to attach poles together you will damage your pole or pole cap.
CARDBOARD
NOTE
:
When slamming
poles together make sure to
keep the poles
STRAIGHT.
10-12”
WARNING
!
KEEP FEET AWAY WHEN
SLAMMING POLE.
6
TOOLS REQUIRED FOR THE FOLLOWING STEPS
1 - 15/16" Open end Wrench
1 - 15/16” Socket and Ratchet (optional)
1 - 9/16” Deep Well Socket & Ratchet
1 - 3/4” Socket & Ratchet
1 - 3/4” Open end Wrench
1 - Phillips Screwdriver
1 - Level
1 - Tape Measure
1 - Rubber Mallet
1 - Set of Padded
Saw Horses
1 - 9/16” Open end Wrench
1 - Cordless drill & 9/64” drill bit
1 - 5/16” socket driver (for cordless drill)
1 - Safety glasses
1 - Ladder
ASSEMBLY INSTRUCTIONS (Day 5)
Figure 3B
Figure 3A
NOTCHES IN BASE
PLATE MUST BE ON
SIDE AS SHOWN
FRONT
BACK
SIDE
Be sure that the
“Back Side”
stickers are at the
back of the poles.
BACK SIDE
PIECE OF
CARDBOARD
Must be at least as
big as pole base plate.
FAILURE TO FULL
Y ENGAGE THE
BOTTOM OF THE UPPER POLE TO
THE 6” MARK ON THIS BOTTOM
POLE STICKER, COULD CAUSE
YOUR UNIT TO COLLAPSE AND MAY
RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE.
BACKSIDE
Bottom
of
upper
pole
must
cover
the
above
orange
portion
of
this
sticker
(6” mark).
WARNING
!
4L-8151-00
FAILURE TO FULLY ENGAGE THE
BOTTOM OF THE UPPER POLE TO
THE 6” MARK ON THIS BOTTOM
POLE STICKER, COULD CAUSE
YOUR UNIT TO COLLAPSE AND MAY
RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE.
BACKSIDE
Bottom of upper pole must cover the
above orange portion of this sticker
(6” mark).
WARNING
!
4L-8151-00
NOTE
: Top Pole must cover upper
orange area of sticker. If Pole goes
slightly past the 6” mark, it is OK
.
1.
Before putting any of the poles tubes together, make sure that the orange area
of the Warning Sticker on Pole (#2) is 6 inches from the top end.
Be sure that
the “Back Side” stickers are at the back of the pole.
See
Figure 3A.
WARNING: This pole assembly is heavy. Step 2 will require two adults.
Make sure you can control the pole when slamming it together. Have a
helper stand on the opposite side of the pole. Attention should be paid
to one’s feet and toes during entire slamming process.
2.
2.
Align the upper pole (#3) with the bottom pole (#2) as shown in
Figure 3A
and
slide them together. While maintaining control of the pole assembly stand poles
up
STRAIGHT
on a piece of cardboard from your box,
lift poles up by bottom
pole
below the 6” mark shown on sticker and slam down the bottom pole as
many times as needed on the cardboard
until the bottom of the upper pole
reaches the 6”
mark (on Sticker) on the bottom pole. Lift the pole 10-12 inches
off the ground when slamming the poles together.
See Figure 3A & 3B
.
Should any concerns exist about damaging your driveway, use a 12” X 12” piece
of Plywood or mdf board.
NOTE:
When slamming poles together make sure to keep the poles
STRAIGHT.
Slamming the poles down crooked will damage the bottom of
the pole and base plate. Top Pole must cover upper orange area of sticker.
If Pole goes slightly past the 6” mark, it is OK.
IMPORTANT! DO NOT hit poles with hammer or sledge hammer
to attach poles together you will damage your pole or pole cap.
CARDBOARD
NOTE
:
When slamming
poles together make sure to
keep the poles
STRAIGHT.
10-12”
WARNING
!
KEEP FEET AWAY WHEN
SLAMMING POLE.
NOTE:
When Slamming the pole together
make sure you
place the cardboard on a
flat surface
like concrete or
Asphalt, do not slam pole on grass or soft ground.
