background image

 

Here are some maintenance tips required to insure safe enjoyment of your equipment for years to come.

A. At the beginning of each usage season and every two weeks during, check: nuts and bolts and tighten as needed, 

swing seats, chains, and wood components for signs of deterioration and replace if necessary.

B. On a yearly basis, we recommend that you coat your playset with a sealant or preservative. You may also want to spot 

sand any areas prior to sealing. Be sure that the sealant you select is non-toxic and child safe. 

C. Remove plastic swing seats and take indoors or do not use when the temperature drops below 0

º

 F.

Choosing A Location For Your Playset

Do not install home playground equipment indoors, 

or over concrete, asphalt, packed earth, grass, carpet 

or any other hard surface. A fall onto a hard surface 

can result in serious or fatal injury.

Responsible on-site adult supervision is one of the 

most important contributions to children’s safety that 

you can make. Jack & June strongly recommends on-

site adult supervision of children of all ages. Safe 

swinging skills need to be taught to children, just like 

any other physical activity.

The weight limit for any single user on Jack & June 

play equipment is 200 pounds. Limit the number of 

users to one on each swing. 

When the time comes to disassemble and dispose of 

the play equipment, do so in such a way that no 

hazards will exist at the time the equipment is 

discarded.

 

If you have any questions about your playset, or are in need of replacement parts, call 1-800-GO-SWING.

 Please keep these instructions for future reference.

Maintaining Your Playset

I N T R O D U C T I O N

When selecting your structure site, always keep the 

child’s safety in mind. Here are some recommendations

to help you create a safe play area.

A. The playset should be located on level ground. The

stationary components are

 to be a minimum 

 REQUIRED

of six feet from any structure or obstruction such as a 

fence, garage, house, tree or overhanging branches, 

electrical wires or clotheslines.

Any swinging equipment is also 

 to be a 

REQUIRED

minimum distance twice the height of the swing beam 

away from these obstructions or structures as well. We 

also recommend that you do not install your playset 

near a lake, river, swimming pool or other water hazard.

B. 

The U.S. Consumer Product Safety Commission (CPSC) 

recommends that you install and maintain a resilient 

surface under your play equipment. The CPSC’s 

Consumer Information Sheet for Playground Surfacing 

Materials at the end of this manual. A resilient surface, 

should be installed after the equipment has been 

completely assembled according to these instructions. 

The equipment must rest on solid ground. Please note 

that this product has a maximum fall height of 8’.

2

Summary of Contents for Jack & June PG9000W












Reviews: