User Manual
6
Remote Buttons
Model
Rated Voltage
8m
3.0V(Dry batteries R03/LR03
×
2)
O
O
-5 C~60 C
Remote Controller Specifications
1. Operating Mode: AUTO, COOL, DRY, HEAT(enabled on cooling& heating
models only ) and FAN.
2. Timer Setting Function in 24 hours.
。
。
3. Indoor Setting Temperature Range : 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display).
Environment
Signal Receiving
Range
Performance Feature
3
4
,
RG52E1/BGEF RG52E2/BGEF
Function buttons
ON/OFF
MODE
FAN
TEMP
ECO
TIMER ON
TIMER OFF
SLEEP
LED FOLLOW ME
TURBO SELF CLEAN
1
2
Each time the button is pressed, the operation
mode is selected in a sequence of following:
3
MODE Button
4
5
ON/OFF Button
Operation starts when this button is pressed
and stops when this button is pressed again.
NOTE:
Heat mode is for Cooling & Heating models only.
AUTO
COOL
DRY
HEAT
FAN
6
7
SELF CLEAN Button
Used to select the fan speed in four steps:
AUTO LOW MED HIGH
FAN Button
Active/Disable Self Clean function
SLEEP Button
NOTE:
While the unit is running under SLEEP
mode, it would be cancelled if MODE, FAN
SPEED or ON/OFF button is pressed.
Active/Disable sleep function. It can maintain
the most comfortable temperature and save
energy. This function is available on COOL,
HEAT or AUTO mode only .
TURBO Button
LED Button
Disable/Active indoor screen Display. When
pushing the button, the indoor screen display
is cleared, press it again to light the display.
1
2
4
5
3
9
8
10
6
7
11
12
14
ON/OFF
MODE
FAN
SLEEP
TEMP
ECO
TIMER ON
TIMER OFF
LED FOLLOW ME
TURBO SELF CLEAN
Active/Disable Turbo function. Turbo function
enables the unit to reach the preset temper-
ature at cooling or heating operation in the
shortest time(if the indoor unit does not
support this function, there is no
corresponding operation happened when
pressing this button.)
ON/OFF
MODE
FAN
TEMP
ECO
TIMER ON
TIMER OFF
SLEEP FRESH
SWING DIRECT
LED FOLLOW ME
TURBO SELF CLEAN
RG52E2/BGEF
RG52E1/BGEF
RG52E1/BGEF
5
6
TIMER ON Button
TIMER OFF Button
UP Button( )
Push this button to decrease the indoor
o
o
temperature setting in 1 C increments to 17 C.
DOWN Button( )
8
10
12
11
13
14
Press this button to initiate the auto-on time
sequence. Each press will increase the auto-
timed setting in 30 minutes increments. When
the setting time displays 10.0, each press will
increase the auto-timed setting 60 minutes
increments. To cancel the auto-timed program,
simply adjust the auto-on time to 0.0.
Press this button to initiate the auto-off time
sequence. Each press will increase the auto-
timed setting in 30 minutes increments. When
the setting time displays 10.0, each press will
increase the auto-timed setting 60 minutes
increments. To cancel the auto-timed program,
simply adjust the auto-off time to 0.0
Push this button to increase the indoor
o
o
temperature setting in 1 C increments to 30 C.
FOLLOW ME Button:
Push this button to initiate the Follow Me
feature, the remote display is actual tempera-
ture at its location. The remote control will
send this signal to the air conditioner every 3
minutes interval until press the Follow Me
button again. The air conditioner will cancel
the Follow Me feature automatically if it does
not receive the signal during any 7 minute
interval.
Swing Button
(applicable for RG52E1/BGEF)
Swing Button
(applicable for RG52E1/BGEF)
Used to stop or start horizontal louver move-
ment or set the desired up/down air flow
direction. The louver changes 6 degree in angle
for each press. If keep pushing more than 2
seconds, the louver will swing up and down
automatically.
Used to stop or start vertical louver movement
and set the desired left/right air flow direction.
The vertical louver changes 6 degree in angle
for each press. If keep pushing more than 2
seconds, the vertical louver auto swing feature
is activated.
1
1
2
2
4
4
5
5
3
3
9
9
8
8
10
10
6
6
7
7
11
11
12
12
13
14
14
ON/OFF
ON/OFF
MODE
MODE
FAN
FAN
SLEEP
TEMP
TEMP
ECO
ECO
TIMER ON
TIMER ON
TIMER OFF
TIMER OFF
LED FOLLOW ME
LED FOLLOW ME
TURBO SELF CLEAN
TURBO SELF CLEAN
9
Used to enter the energy efficient mode.
Under cooling mode, press this button, the
remote controller will adjust the temperature
O
automatically to 24 C, fan speed of Auto to
save energy(but only if the set temperature
O
is less than 24 C). If the set temperature is
O
O
between 24 C and 30 C, press the ECO
button, the fan speed will change to Auto,
the set temperature will remain unchanged.
NOTE:
Pressing the TURBO and SLEEP button,
modifying the mode or adjusting the set
O
temperature to less than 24 C will stop
ECO operation.
Under ECO operation, the set temperature
O
should be 24 C or more. it may result in
insufficient cooling. If you feel uncomfortable,
just press the ECO button again to stop it.
ECO Button:
RG52E1/BGEF
SLEEP FRESH
SWING DIRECT
SWING Button
(applicable for RG52E2/BGEF)
DIRECT Button
(applicable for RG52E2/BGEF)
Used to change the louver movement and set
the desired up/down air flow direction.
O
The louver changes 6 in angle for each press.
Used to stop or start horizontal louver auto
swing feature.
FRESH Button
(applicable for RG52E2/BGEF)
Active/Disable
When the
FRESH function is initiated, the Ionizer/
Plasma Dust Collector(depending on
models) is energized and will help to
remove pollen and impurities from the air.
FRESH function.
RG52E1 - UserManual_V1.indd 6
17/5/19 10:43 am