User Manual
20
SPRAY ARMS
It is necessary to clean the spray arms regularly for
hard water chemicals will clog the spray arm jets and
bearings.
To clean the spray arms, follow the instructions below:
STEP 1:
To remove the upper spray arm, hold the nut in the
center still and rotate the spray arm counterclockwise
to remove it.
STEP 2:
To remove the lower spray arm, pull out the spray
arm upward.
STEP 3:
Wash the arms in soapy and warm water and use a
soft brush to clean the jets. Replace them after rinsing
them thoroughly.
CARING FOR THE DISHWASHER
Frost precaution
Please take frost protection measures on the
dishwasher in winter. Every time after washing cycles,
please operate as follows:
1. Cut off the electrical power to the dishwasher at
the supply source.
2. Turn off the water supply and disconnect the water
inlet pipe from the water valve.
3. Drain the water from the inlet pipe and water valve.
(Use a pan to gather the water)
4. Reconnect the water inlet pipe to the water valve.
5. Remove the filter at the bottom of the tub and use
a sponge to soak up water in the sump.
After every wash
After every wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odors are not trapped inside.
Remove the plug
Before cleaning or performing maintenance, always
remove the plug from the socket..
No solvents or abrasive cleaning
To clean the exterior and rubber parts of the
dishwasher, do not use solvents or abrasive cleaning
products. Only use a cloth with warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened with water an a little
vinegar, or a cleaning product made specifically for
dishwashers.
After prolonged inactivity
It is recommend that you run a wash cycle with the
dishwasher empty and then remove the plug from the
socket, turn off the water supply and leave the door
of the appliance slightly open. This will help the door
seals to last longer and prevent odours from forming
within the appliance
Moving the appliance
If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.
Seals
One of the factors that cause odours to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
Spray arms
Wash the arms in soapy and warm
water and use a soft brush to clean
the jets. Replace them after rinsing
them thoroughly.
It is necessary to clean the spray arms regularly for hard water chemicals will clog the
spray arm jets and bearings.
To clean the spray arms, follow the instructions below:
2
3
To remove the lower spray arm, pull
out the spray arm upward.
13
1
To remove the upper spray arm,
hold the nut in the center still and
rotate the spray arm counterclockwise
to remove it.
Spray arms
Wash the arms in soapy and warm
water and use a soft brush to clean
the jets. Replace them after rinsing
them thoroughly.
It is necessary to clean the spray arms regularly for hard water chemicals will clog the
spray arm jets and bearings.
To clean the spray arms, follow the instructions below:
2
3
To remove the lower spray arm, pull
out the spray arm upward.
13
1
To remove the upper spray arm,
hold the nut in the center still and
rotate the spray arm counterclockwise
to remove it.
Spray arms
Wash the arms in soapy and warm
water and use a soft brush to clean
the jets. Replace them after rinsing
them thoroughly.
It is necessary to clean the spray arms regularly for hard water chemicals will clog the
spray arm jets and bearings.
To clean the spray arms, follow the instructions below:
2
3
To remove the lower spray arm, pull
out the spray arm upward.
13
1
To remove the upper spray arm,
hold the nut in the center still and
rotate the spray arm counterclockwise
to remove it.
Cleaning & Maintenance (Continued)
