background image

PT-19XL PLASMARC CUTTING TORCH

SECTION 2

REQUIRED EQUIPMENT

2.1   AIR CUTTING - 150 AMPS*

A. PCC-11/PT-19XL Package P/N 604472

Which includes:

PCC-11 Control, P/N 16367
PT-19XL Torch, 50 ft Lines, P/N 20390
PT-19XL Start-Up Kit, P/N 20964
Gas Hose, 12.5 ft, P/N 40V77
Water Hose (2), 3 ft, P/N 20634
Air Hose, 30", P/N 678152
WC-8C Coolant Circulator, P/N 33739
Work Cable, 50 ft, P/N 678724
Mounting Bracket, P/N 20961
Adaptor, Pilot Arc, P/N 19497

*For oxygen cutting up to 150 amps, use above re-
quired equipment and replace air regulator P/N 30338
with oxygen regulator P/N 998336 and add oxygen
hose P/N 678725.

B. PCM-150 (P/N 30850) or PCM-1500 (P/N

680851) Power Source

C. Air Regulator, P/N 30338

D. Nitrogen Regulator, P/N 998343 (Cylinder) or

P/N 19155 (Station)

E. Torch Coolant (1 gal.), P/N 156F05.  Four

gallons of coolant will be required.

2.3  OXYGEN CUTTING - 260 AMPS WITH
       ESP-1000 SYSTEM

A. ESP-1000 System, contact your ESAB Sales
    Representative.

B. ESP-300, P/N 33520, or ESP-400, P/N 33518.

2.4  ACCESSORIES

A. PT-19XL Torch Spare Parts Kit, P/N 34314--

Recommended for maintaining the PT-19XL torch
with minimum downtime. The kit contains the follow-
ing PT-19XL parts and tools:

4 - Electrode, Long ................................... P/N 34086
4 - Electrode, Long N

2

/ArH

2

...................... P/N 34557

1 - Electrode Holder ................................. P/N 34084
5 - Nozzle, 50A ......................................... P/N 34730
5 - Nozzle, 150 A ...................................... P/N 21821
5 - Nozzle, 250A ....................................... P/N 21822
4 - Gas Swirl Baffle ................................. P/N 948142
1- Nozzle Retaining Cup .......................... P/N 34085
1- Insulator Assembly ............................... P/N 20434
1- Contact Ring Assembly ........................ P/N 20395
10 - O-Ring ............................................. P/N 86W85
10 - O-Ring ............................................. P/N 996526
20 - O-Ring ............................................. P/N 951000
20 - O-Ring ............................................. P/N 996528
10 - O-Ring ............................................. P/N 86W99
20 - O-Ring ............................................. P/N 85W10
1- Nozzle & Electrode Stem Tool ........... P/N 999630
1- Electrode Tip Removal Tool ............... P/N 996568
1- Hex Wrench, 1/16" ......................... P/N 93750006
1- Silicone Grease .................................... P/N 17672
2 - Heat Shield 50A .................................. P/N 34885
2 - Heat Shield 150/250A ....................... P/N 948186

1.  Torch Clamp Assembly, P/N 598707, or Univer-
     sal Clamp Assembly, P/N 598699, is required for
     mounting the PT-19XL.
     For stationary or boom mounting, the following    
     parts may also be needed:
     Rack & Tube Assembly, P/N 39V35
     Torch Adjustment Assembly, P/N 40V26
     Adjustable Slide, P/N N25V39
     Angle Bracket, P/N 29N04
     Clamp Insulator Bushing P/N 996342

2.  For mounting on a CM-37 Carriage, mounting kit
     P/N 993092 may be used.  The kit contains
     Clamp Assembly P/N 598707.

B. Torch Mounting

C. Air Curtain Kit - P/N 34752 , consisting of :

21549 Air Curtain Assembly
33383 Control Panel
34033 Hose, 50 ft.

 The air curtain directs a flow of air around the arc
which permits underwater cutting with O

2

 gas. See

Form 15-128 for details.

3.  For cutting machine operation, the torch will
     mount on a standard PT-15 torch mounting
     setup.

Note: Underwater cutting cannot be done with 50A
          nozzle.

4

Summary of Contents for PT-19A













Reviews: