SECTION 1
SAFETY
1-4
1.5 Electrical Grounding
Electrical grounding is imperative for proper machine
operation and SAFETY. Refer to this manual’s
Installation section for detailed grounding instructions.
WARNING
!
Electric shock hazard.
Improper grounding can cause severe injury or death.
Improper grounding can cause severe injury or death.
Improper grounding can cause severe injury or death.
Improper grounding can cause severe injury or death.
Machine must be properly grounded before put into
Machine must be properly grounded before put into
Machine must be properly grounded before put into
Machine must be properly grounded before put into
service.
service.
service.
service.
WARNING
!
Improper grounding can damage machine
and electrical components.
•
Machine must be properly grounded before put
Machine must be properly grounded before put
Machine must be properly grounded before put
Machine must be properly grounded before put
into service.
into service.
into service.
into service.
•
Cutting table must be properly grounded to
Cutting table must be properly grounded to
Cutting table must be properly grounded to
Cutting table must be properly grounded to
a good
a good
a good
a good
Earth ground rod.
Earth ground rod.
Earth ground rod.
Earth ground rod.
1.6 Operating A Plasma Cutting Machine
WARNING
!
Flying debris and loud noise hazards.
•
Hot spatter can burn and injure eyes. Wear
Hot spatter can burn and injure eyes. Wear
Hot spatter can burn and injure eyes. Wear
Hot spatter can burn and injure eyes. Wear
goggles to protect eyes from burns and flying
goggles to protect eyes from burns and flying
goggles to protect eyes from burns and flying
goggles to protect eyes from burns and flying
debris generated during operation.
debris generated during operation.
debris generated during operation.
debris generated during operation.
•
Chipped slag may be hot and fly far. Bystanders
Chipped slag may be hot and fly far. Bystanders
Chipped slag may be hot and fly far. Bystanders
Chipped slag may be hot and fly far. Bystanders
should also wear goggles and safety glasses.
should also wear goggles and safety glasses.
should also wear goggles and safety glasses.
should also wear goggles and safety glasses.
•
From plasma arc can damage hearing. Wear
From plasma arc can damage hearing. Wear
From plasma arc can damage hearing. Wear
From plasma arc can damage hearing. Wear
correct ear protection when cutting above water.
correct ear protection when cutting above water.
correct ear protection when cutting above water.
correct ear protection when cutting above water.
WARNING
!
Burn hazard.
Hot metal can burn.
Hot metal can burn.
Hot metal can burn.
Hot metal can burn.
•
Do not touch metal plate or parts immediately after
Do not touch metal plate or parts immediately after
Do not touch metal plate or parts immediately after
Do not touch metal plate or parts immediately after
cutting. Allow metal time to cool, or douse with
cutting. Allow metal time to cool, or douse with
cutting. Allow metal time to cool, or douse with
cutting. Allow metal time to cool, or douse with
water.
water.
water.
water.
•
Do not touch plasma torch immediately after
Do not touch plasma torch immediately after
Do not touch plasma torch immediately after
Do not touch plasma torch immediately after
cutting. Allow torch time to cool.
cutting. Allow torch time to cool.
cutting. Allow torch time to cool.
cutting. Allow torch time to cool.
Summary of Contents for Precision Plasmarc
