manualshive.com logo in svg

Ericsson EDN612, Installation Manual, Page: 11 / 28

Share
Download
Ericsson EDN612 Installation Manual Download Page 11

Power Requirements and Distribution 

 
 

3/1531-HSD 101 41 Uen E  2007-08-13

 

7

 

4 

Power Requirements and Distribution 

EDN612 and ESN212 use -48 volt power supply. Either High Ohmic 
distribution system, or independent power distribution (Standard -48V 
telecom supply) according to ETSI EN 300 132-2 v2.1.2 (2003 09) can be 
used. 15A fuse is required. It is recommended to use EPN210 for the 
power distribution as illustrated in the following figure: 

 

Figure 3 

Recommended Power Distribution 

If another power distribution unit is used instead of the EPN210, it is 
possible to use the TSR 263 65/xxx cables (EDA Power Cable Open End). 

A solution to omit the EPN210, and use the 5:1 power distribution cable as 
illustrated in the following figure: 

 

Figure 4 

Power Distribution 

Note:

  The fuse is not part of any cable, and is purchased separately. 

 
-48 VDC 

Fuse 

10 – 15A 

EDN612 

EDN612 

ESN212 

Cable: TSR 263 72/xxx 

(EDA Power cable 5:1 open ended)

 

 
-48 VDC 

Fuse 

15A 

EDN612 

EDN612 

ESN212 

Cable: TSR 263 69/3000 

(EDA D-Sub Power cable open 

ended)

 

Cable: TSR 263 70/600 

(EDA Power cable standard)

 

 
EPN210 

Summary of Contents for EDN612





























Reviews:

No comments