TROUBLESHOOTING
Each IF amplifier has a nominal 18 dB gain. U2 has a
nominal gain of 30 dB. The mixer has about 20 dB gain with
proper LO injection. The proper crystal oscillator level is 50
mV pk measured at TP3.
The following four test points are provided on the PWB for
additional test capability:
TP1:
100 mV pk @ 21.4 MHz with -30 dBm input sig-
nal
TP2:
100 mV PK @ 21.4 MHz with -50 dBm input
signal
TP3:
50 mV pk @ 20.945 MHz independent of input
signal
TP4:
100 mV pk @ 455 kHz with -60 dBm input sig-
nal
All RF voltages measured with 10 Megohm, 11 pF probe.
ASSEMBLY DIAGRAM
TROUBLE SHOOTING GUIDE
SYMPTOM
CHECK
(CORRECT READING SHOWN)
INCORRECT READING
INDICATES DEFECTIVE
COMPONENT
Fault indicator on
Check DC voltages
+8V at U8 Pin 1
+4v at U Pin 7
5.5V at U1 output pin
3.3V at 2 output pin
4.4V at U3 Pin 4
If DC voltages not correct
U8 or associated components
U6 or associated components
U1 or associated components
U2 or associated components
U3 or associated components
If DC voltages correct
U4, U5, U6, D1, Q3, Q4, Q5
No audio - no
noise
With no signal applied to module IF input
Check for AF noise @ C29 ; 200mV
Check for AF noise @ U6 Pin 8: 1 V
U3 or associated components
U6 or associated components
Noise only - no
demodulated audio
Check crystal oscillator: TP3 50 mVpk 20.945 MHz
Apply -30 dBm 21.4 MHz input, check TP1 100 mVpk
Apply -50 dBm 21.4 MHz input, check TP2 100 mVpk
Apply -60 dBm 21.4 MHz input, check TP4 100 mVpk
U3, Y3 or associated components
Q6, Y1, U1 or associated components
U2, Y2 or associated components
U3, FL1 or associated components
Poor 12 dB SINAD
Check crystal oscillator: TP3 50 mVpk 20.945 MHz
U3, Y3 or associated components
Apply -30 dBm 21.4 MHz input, check TP1 100 mVpk
Apply -50 dBm 21.4 MHz input, check TP2 100 mVpk
Apply -60 dBm 21.4 MHz input, check TP4 100 mVpk
Q6, Y1, U1 or associated components
U2, Y2 or associated components
U3, FL1 or associated components
No squelch
function
With squelch pot maximum, or with module AUDIO/
SQUELCH/HI connected to SQUELCH/ARM input
and with no signal to module IF input:
Check Presence of 1 Vpk noise at U6 Pin 14
U6 or associated components
Check presence of 1 Vpk noise U7 at Pin 1
Check presence of 1 Vpk noise U7 Pin 1
Check DC voltage U7 at Pin 8: 7 V
Check DC voltage U7 Pin 14: 0.5 V
U7 or associated components
RECEIVER IF MODULE
19D902783G1
(19D902783, Sh. 1, Rev. 3)
LBI-38643C
3
Summary of Contents for 19D902783G1
