background image

 

EG_GenProxxe_988_UG_008_UK 

Page 25 / 51

 

 

Descriptions and non-contractual illustrations in this document are given as an indication only. 

 ERCO&GENER reserves the right to make any modifications. 

5.8 Main AT commands (HAYES) 

 

The table below shows at a quick glance the main AT commands useful for the control of the modem. 

For further information concerning the complete command set see the Wavecom "AT Commands Interface 

Guide" and the ERCO&GENER "Commands List”. 

 

Table : Main AT commands used with the modem. 

Description 

AT Command 

Response 

Interpretation 

Enter the PIN code 

AT+CPIN=xxxx 

OK 

PIN code accepted 

(xxxx = PIN code) 

+CME ERROR: 16 

PIN code incorrect (1*) 

 

+CME ERROR: 3 

PIN code already entered (1*) 

Verification of GSM 
network registration 

AT+CREG? 

+CREG: 0,0 

The modem is not recognised by the 
network. 

 

+CREG: 0,2 

The modem is searching for a 
network operator. 

 

+CREG: 0,1 

The modem is GSM attached to a 
local operator. 

 

+CREG: 0,5 

The modem is GSM attached to an 
operator in roaming mode. 

Reception of an 
incoming call (2*) 

ATA 

OK 

Reply to the call 

Make a voice call 

ATD<telephone 
number>; 

OK 

Communication established 

(IMPORTANT: the 

;

 at 

the end of the sequence 
specifies a voice call) 

+CME ERROR: 11 

PIN code not entered 

+CME ERROR: 3 

The credit has run out or the 
communication has already been 
established. 

Make an emergency 
call (112) 

ATD112; 

OK 

Communication established 

Lost communication   

NO CARRIER 

 

Hang-up ATH 

OK 

 

 

(1*) The command 

AT+CMEE=1 

 allows the display of extended error codes. This command may be saved 

with the command 

AT&W

.  

The command 

AT+WIND=63 

allows the display of the change of status of the SIM card (present, 

ready…) and to check divers modem states (modem ready after RESET…). This command may be 

saved with the command 

AT&W

(2*) The command 

AT+CRC=1 

will in the case of an incoming call, display more detailed ring information 

indicating the type of call - voice, data or fax. This command may be saved with the command 

AT&W

Examples : 

For VOICE : +CRING: VOICE  

For DATA :  +CRING: REL ASYNC 

For FAX :  +CRING: FAX 

 

Summary of Contents for GenPro 20e




















































Reviews: