manualshive.com logo in svg

Equustek DL6000, User Manual

Share
Download
Equustek DL6000 User Manual Download Page 27

       

#286-5489 Byrne Rd., Burnaby, BC, V5J3J1, Canada          Phone: 888-387-3787 or 604-266-8547              www.equustek.com

 

27

below to configure the DL6000-MEDH+.  A new window should appear with the 

following menu in the text box. 

 
BIOS MANAGER for DL6000-1.00-  Jun 16,06 
     (c) Equustek Solutions Inc. 2006 
 
            MAIN MENU 
 
  1 - Restore EEPROM 
  2 - WRITE new Firmware 
 
  3 - Memory DUMP 
  4 - OFF-LINE Diagnostics 
  5 - DEBUG Mode 
 
  6 - FIRMWARE Version 
  7 – ONLINE 
  8 - CONFIGURE Model Parameters 
 
  MAKE SELECTION (1-8) - 

 

1.

 

Press 8 to configure the Modbus Parameters.  The following will appear. 

 

Enter Modbus Translation table parameters for Modicon to AB mapping. 
AT Any time hit <ENTER> To Keep existing parameter value 
Hit <ENTER> To continue, <ESC> to exit 
 
 
 
 

2.

 

Press Enter to continue.  You will then be asked to select a PLC type that the DL6000 

will be communicating to. 

 

Select A-B PLC TYPE: SLC/Micrologix 
Enter 0 for PLC5, 1 for PLC3 or 2 for SLC or Micrologix or <ENTER> to keep: 
 
 
 

3.

 

After selecting the PLC type you will then be asked to enter the values for the 

translation table.  Leading zeros need to be entered when using the DL Offline 

Manager to configure the DL6000.  After entering the translation parameters, press 

Enter to proceed to the end of the table. 

  

Program Modbus/A-B Translation Parameters 
Hit <ENTER> to keep exsiting value or Type in New Value 
Need to enter Leading Zeros. IE. file 7 = 007 
Hit <ENTER> to Proceed any other key to exit now. 
 
 
 
REC No  Modbus Start Add.  Modbus End Add.  A-B Start Address  Floating Point 
                                              

(File:Word)    

            xxxxx              xxxxx           xxx:xxx           Yes/No 
 
   00       40001              40010           007:000             N 
   01       30001              30010           008:000             N 
   02       00001              00016           003:000             N 
   03       00000              00000           000:000             N 
   04       00000              00000           000:000             N 
   05       00000              00000           000:000             N 
   06       00000              00000           000:000             N 
   07       00000              00000           000:000             N 

Summary of Contents for DL6000











































Reviews:

No comments

Brands by name

Popular brands

Load more brands