manualshive.com logo in svg

Equipment Technologies APACHE AS1010, Owner'S Manual, Page: 76 / 124

Share
Download
Equipment Technologies APACHE AS1010 Owner'S Manual Download Page 76

LUBRICATION AND MAINTENANCE

5-10

Check Transmission Fluid Level

The transmission fluid dipstick is located in
the engine compartment, on the left side of
the engine.

Turn the handle counter-clockwise to loosen.
Remove the dipstick and check the transmis-
sion fluid level.

The fluid level should be between the two
dots on the dipstick.

IMPORTANT: DO NOT overfill the transmis-
sion fluid. Overfilling can damage the trans-
mission or cause the transmission to
malfunction or overheat.

IMPORTANT: Use only Lucas Universal
Hydraulic Fluid.

If the fluid level is below the lower dot on the
dipstick, use a funnel to add fluid through the
dipstick tube.

Add Lucas Universal Hydraulic Fluid to bring
the level between the dots on the dipstick.

Replace the dipstick and turn the handle
clockwise to tighten.

ITL/JBC Transmission (AS1010)

IMPORTANT: Check the transmission fluid
level with the oil warm and the engine turned
off.

Funk Transmission (AS1210 and
optional equipped AS1010)

IMPORTANT: Check the transmission fluid
level with the engine running, the transmis-
sion at normal operating temperature, and
the transmission in neutral position.

Summary of Contents for APACHE AS1010





























































































































Reviews:

No comments