background image

 Equinox Trinity Beam Laser 

 

 

 

 

 

 

 

 

     Safety

What harm can a Class 3B Laser cause?

Class 3B laser devices can be harmful to eyesight if viewed directly. i.e. that is, the beam or effect 

strikes the face of a person. The actual injury that a Class 3B laser can cause depends upon a 

number of factors, including how long the laser beam enters the eye for, the intensity of light, and 

what part of the eye it actually gets focused onto. The most susceptible part of the eye to receive 

damage from a laser is the internal back wall of the eyeball, known as the retina. It is this part of 

the eye that receives the light signals that are sent to brain. All light entering the eye gets focused 

onto the retina.

Normal light sources such as traditional light bulbs and regular lighting effects are normally not 

harmful to view. Lasers differ in that they can get focused down to very small points on the retina 

that can literally burn holes on the back of the eye, which can lead damage to eyesight. This 

process can happen in less time than it takes for a person to blink. There are no pain receptors 

on the retina, so the person will be unaware of any damage taking place. Damage caused to the 

retina is permanent, and can vary from unnoticeable loss of vision, through to severe loss of sight, 

particularly if the damage occurs in the part of the retina that senses the central vision.

Are there any laws or licences relating to using Class 3B lasers?

There are no specific “laser licences” that anybody needs in order to own or operate a laser for 

lightshow use. However, there is specific guidance issued by the Health and Safety Executive in 

the form of a document called HS(G)95 The Radiation Safety of Lasers Used for Display 

Purposes. HS(G)95 outlines a number of detailed points to consider when using lasers for 

lightshow purposes.

Furthermore, since April 2010 new health and safety legislation was introduced in the UK that sets 

legal limits as to the amount of laser light a person may be exposed to in the workplace. Class 3B 

lasers have the ability to exceed the safety limits. The full title of the laser safety regulations is the 

Control of Artificial Optical Radiation at Work Regulations 2010, which also define the need for risk 

assessment of the exposure levels.

Most places of public entertainment operate under a Public Entertainments Licence, which is 

issued by the Local Authority. The entertainment licence requirements will normally need to have a 

specific provision covering the use of lasers at the venue, where it is expected that the laser instal-

lation, (whether temporary or permanent), is to operated in compliance with the HS(G)95 laser 

safety guidance as part of the venue’s Public Entertainment Licence conditions.

The use of lasers, as any other equipment used for shows, will also be covered by more general 

health and safety legislation, such as the Health & Safety at Work Act 1974, and the Management 

of Health and Safety at Work Regulations 1999, etc. These regulations, among other things, state 

that you must ensure the safety of people present at the event where the laser is used, and also 

that a suitable risk assessment regarding the use of laser must be carried out.

Summary of Contents for EQLA42





















Reviews: